Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1800/51  Short in Driver Side Squib Circuit  B1801/51  Open in Driver Side Squib Circuit  B1802/51  Short to GND in Driver Side Squib Circuit  B1803/51  Short to B+ in Driver Side Squib Circuit  


DESCRIPTION

The driver side squib circuit consists of the center airbag sensor, the spiral cable and the steering pad.

The circuit instructs the SRS to deploy when the deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the driver side squib circuit.


DTC Code Detection Condition Trouble Area
B1800/51 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the driver side squib circuit during primary check.

·

Driver side squib malfunction

·

Spiral cable malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Center airbag sensor assembly


B1801/51 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the driver side squib circuit for 2 seconds.

·

Driver side squib malfunction

·

Spiral cable malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Center airbag sensor assembly


B1802/51 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the driver side squib circuit for 0.5 seconds.

·

Driver side squib malfunction

·

Spiral cable malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Center airbag sensor assembly


B1803/51 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the driver side squib circuit for 0.5 seconds.

·

Driver side squib malfunction

·

Spiral cable malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Center airbag sensor assembly



WIRING DIAGRAM

U152127E01
2.184,1.566 2.409,1.722 0.225,0.156 10 D+ 2.183,2.407 2.360,2.562 0.177,0.156 10 D- 4.794,1.664 5.019,1.820 0.225,0.156 10 D+ 4.794,2.505 4.971,2.660 0.177,0.156 10 D- 3.232,1.769 3.457,1.960 0.225,0.191 10 1 3.232,2.61 3.408,2.800 0.177,0.191 10 2 2.685,2.995 2.959,3.158 0.274,0.163 10 J11 2.685,3.15 3.494,3.320 0.809,0.170 10 Spiral Cable 1.165,3.15 2.335,3.306 1.170,0.156 10 Driver Side Squib 4.591,1.552 4.754,1.791 0.163,0.239 10 5 4.591,2.385 4.830,2.611 0.239,0.225 10 6 4.808,4.165 5.096,4.307 0.288,0.142 10 J46 4.808,4.327 6.186,4.497 1.378,0.170 10 Center Airbag Sensor 1.165,2.995 1.439,3.158 0.274,0.163 10 z4 2.475,2.61 2.701,2.800 0.225,0.191 10 1 2.486,1.769 2.662,1.960 0.177,0.191 10 2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK STEERING PAD (DRIVER SIDE SQUIB)
U152190E02
0.198,0.677 0.198,0.167 0.198,0.167 1.604,0.167 false 2.125,3.313 2.427,3.563 false 1.885,3.813 2.219,4.104 false 1.656,0.083 2.802,0.26 1.146,0.177 10 false Driver Side Squib 0.75,1.24 1.552,1.375 0.802,0.135 10 false Spiral Cable 1.823,1.698 3.24,1.906 1.417,0.208 10 false Center Airbag Sensor 0.479,2.302 2.875,2.667 2.396,0.365 10 false Front view of wire harness connector: (to Driver Side Squib) 0.292,3.073 1.125,3.323 0.833,0.25 10 false Connector E 0.688,3.458 0.917,3.646 0.229,0.188 10 false z4 2.479,3.5 2.844,3.677 0.365,0.177 10 false SST 2.281,4.052 3.198,4.26 0.917,0.208 10 false Color: Orange 0.302,0.927 0.438,1.125 0.135,0.198 10 false F 0.521,0.927 0.656,1.125 0.135,0.198 10 false E 1.667,0.927 1.802,1.125 0.135,0.198 10 false D 1.792,0.917 1.927,1.115 0.135,0.198 10 false C

a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect the z4 connector from the steering pad.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect the tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1800, B1801, B1802 or B1803 is not output.


HINT:

Codes other than DTC B1800, B1801, B1802 and B1803 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect SST from connector E.


d.

Check that the spiral cable connectors (on the steering pad side) are not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.




OK

3.CHECK DRIVER SIDE SQUIB CIRCUIT

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CHECK DRIVER SIDE SQUIB CIRCUIT
a.
U152192E02
0.188,0.771 0.188,0.26 0.188,0.26 1.594,0.26 false 1.875,3.896 2.177,4.146 false 1.677,3.208 1.344,3.5 false 1.802,3.208 2.135,3.5 false 1.635,0.167 2.781,0.344 1.146,0.177 10 false Driver Side Squib 0.76,1.313 1.594,1.521 0.833,0.208 10 false Spiral Cable 1.792,1.708 3.208,1.917 1.417,0.208 10 false Center Airbag Sensor 0.563,2.333 2.958,2.698 2.396,0.365 10 false Front view of wire harness connector: (to Driver Side Squib) 2.25,2.833 3.083,3.083 0.833,0.25 10 false Connector E 0.677,3.521 0.906,3.708 0.229,0.188 10 false z4 2.25,4.083 3.167,4.292 0.917,0.208 10 false Color: Orange 0.313,1 0.448,1.198 0.135,0.198 10 false F 0.531,1 0.667,1.198 0.135,0.198 10 false E 1.667,1 1.802,1.198 0.135,0.198 10 false D 1.781,0.99 1.917,1.188 0.135,0.198 10 false C 2.177,0.99 2.313,1.188 0.135,0.198 10 false B 2.573,0.75 2.708,0.948 0.135,0.198 10 false A 1.24,3.51 1.479,3.688 0.24,0.177 10 false D- 2.125,3.51 2.365,3.688 0.24,0.177 10 false D+

Disconnect the connectors from the center airbag sensor.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
z4-1 (D-) - Body ground Ignition switch ON Below 1 V
z4-2 (D+) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
z4-1 (D-) - z4-2 (D+) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
z4-1 (D-) - z4-2 (D+) Always 1 MΩ or higher
z4-1 (D-) - Body ground
z4-2 (D+) - Body ground




OK

4.CHECK CENTER AIRBAG SENSOR

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
4.CHECK CENTER AIRBAG SENSOR
a.
C158846E12
0.323,0.75 0.365,1.781 false 0.167,1.802 1.948,2 1.781,0.198 10 false Driver Side Squib 0.771,1.083 1.604,1.313 0.833,0.229 10 false Spiral Cable 1.833,1.448 3.177,1.698 1.344,0.25 10 false Center Airbag Sensor 0.552,0.833 0.74,1.021 0.188,0.188 10 false E 0.438,0.833 0.625,1.021 0.188,0.188 10 false F 1.75,0.833 1.938,1.021 0.188,0.188 10 false C 1.635,0.833 1.823,1.021 0.188,0.188 10 false D

Connect the connectors to the steering pad and the center airbag sensor.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1800, B1801, B1802 or B1803 is output (for Column Shift Type) A
DTC B1800, B1801, B1802 or B1803 is output (for Floor Shift Type) B
DTC B1800, B1801, B1802 or B1803 is not output C

HINT:

Codes other than DTC B1800, B1801, B1802 and B1803 may be output at this time, but they are not related to this check.




C

A

B

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
a.
U152194E02
1.75,3.25 1.25,3.719 1.25,3.719 1.156,3.719 false 1.906,3.26 2.385,3.729 2.385,3.729 2.479,3.729 false 1.771,0.24 1.885,0.24 1.885,0.24 1.885,0.948 false 0.354,0.146 1.823,0.323 1.469,0.177 10 false Instrument Panel Wire 0.594,1.479 1.448,1.677 0.854,0.198 10 false Spiral Cable 1.781,1.813 3.198,2.021 1.417,0.208 10 false Center Airbag Sensor 0.49,2.167 2.885,2.531 2.396,0.365 10 false Rear view of wire harness connector: (to Spiral Cable) 2.292,3.177 3.125,3.427 0.833,0.25 10 false Connector C 0.729,2.917 1.031,3.104 0.302,0.188 10 false J11 0.219,1.198 0.354,1.396 0.135,0.198 10 false F 0.417,1.177 0.552,1.375 0.135,0.198 10 false E 1.479,1.167 1.615,1.365 0.135,0.198 10 false D 1.677,1.156 1.813,1.354 0.135,0.198 10 false C 2.344,0.917 2.479,1.115 0.135,0.198 10 false A 1.99,1.146 2.125,1.344 0.135,0.198 10 false B 1.042,3.646 1.167,3.823 0.125,0.177 10 false 2 2.51,3.635 2.615,3.813 0.104,0.177 10 false 1

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Disconnect the instrument panel wire connector from the spiral cable.


c.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
J11-1 - Body ground Ignition switch ON Below 1 V
J11-2 - Body ground



f.

Turn the ignition switch off.


g.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J11-1 - J11-2 Always Below 1 Ω



i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


j.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J11-1 - J11-2 Always 1 MΩ or higher
J11-1 - Body ground
J11-2 - Body ground




OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE