Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1810/53  Short in Driver Side Squib 2nd Step Circuit  B1811/53  Open in Driver Side Squib 2nd Step Circuit  B1812/53  Short to GND in Driver Side Squib 2nd Step Circuit  B1813/53  Short to B+ in Driver Side Squib 2nd Step Circuit  


DESCRIPTION

The driver side squib 2nd step circuit consists of the center airbag sensor, the spiral cable and the steering pad.

The circuit instructs the SRS to deploy when the deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the driver side squib 2nd step circuit.

DTC Code Detection Condition Trouble Area
B1810/53 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the driver side squib 2nd step circuit during primary check.

·

Driver side squib 2nd step malfunction

·

Spiral cable malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib 2nd step)

·

Center airbag sensor assembly


B1811/53 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the driver side squib 2nd step circuit for 2 seconds.

·

Driver side squib 2nd step malfunction

·

Spiral cable malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib 2nd step)

·

Center airbag sensor assembly


B1812/53 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the driver side 2nd step circuit for 0.5 seconds.

·

Driver side squib 2nd step malfunction

·

Spiral cable malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib 2nd step)

·

Center airbag sensor assembly


B1813/53 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the driver side squib 2nd step circuit for 0.5 seconds.

·

Driver side squib 2nd step malfunction

·

Spiral cable malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib 2nd step)

·

Center airbag sensor assembly



WIRING DIAGRAM

C353060E01
4.823,1.677 5.281,1.875 0.458,0.198 10 false D2+ 4.833,2.521 5.292,2.719 0.458,0.198 10 false D2- 2.115,1.583 2.573,1.781 0.458,0.198 10 false D2+ 2.135,2.406 2.594,2.604 0.458,0.198 10 false D2- 2.448,1.781 2.604,1.979 0.156,0.198 10 false 2 2.448,2.625 2.604,2.823 0.156,0.198 10 false 1 3.25,1.771 3.406,1.969 0.156,0.198 10 false 4 3.25,2.625 3.406,2.823 0.156,0.198 10 false 3 4.531,1.563 4.688,1.76 0.156,0.198 10 false 8 4.542,2.417 4.698,2.615 0.156,0.198 10 false 7 0.729,3.031 1.042,3.229 0.313,0.198 10 false z5 0.719,3.219 4.698,3.417 3.979,0.198 10 false Driver Side Squib 2nd Step 2.823,3.031 3.281,3.229 0.458,0.198 10 false J11 2.802,3.208 4.635,3.406 1.833,0.198 10 false Spiral Cable 4.833,4.188 5.292,4.385 0.458,0.198 10 false J46 4.823,4.354 7.156,4.573 2.333,0.219 10 false Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).



PROCEDURE

1.CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)
U152191E02
0.188,0.688 0.188,0.104 0.188,0.104 1.25,0.104 false 1.875,3.833 2.177,4.083 false 2.135,3.281 2.469,3.573 false 1.313,0.01 3.052,0.188 1.74,0.177 10 false Driver Side Squib 2nd Step 0.719,1.208 1.542,1.396 0.823,0.188 10 false Spiral Cable 1.781,1.625 3.198,1.833 1.417,0.208 10 false Center Airbag Sensor 0.563,2.021 2.958,2.385 2.396,0.365 10 false Front view of wire harness connector: (to Driver Side Squib 2nd Step) 0.313,3.115 1.146,3.365 0.833,0.25 10 false Connector E 0.688,3.458 0.917,3.646 0.229,0.188 10 false z5 2.51,3.521 2.875,3.698 0.365,0.177 10 false SST 2.24,4.042 3.156,4.25 0.917,0.208 10 false Color: Black 0.323,0.927 0.458,1.125 0.135,0.198 10 false F 0.531,0.917 0.667,1.115 0.135,0.198 10 false E 1.667,0.917 1.802,1.115 0.135,0.198 10 false D 1.802,0.917 1.938,1.115 0.135,0.198 10 false C

a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect the z5 connector from the steering pad.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).

CAUTION:

Never connect the tester to the steering pad (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1810, B1811, B1812 or B1813 is not output.


HINT:

Codes other than DTC B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect SST from connector E.


d.

Check that the spiral cable connectors (on the steering pad side) are not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.




OK

3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT
U152193E02
0.198,0.76 0.198,0.146 0.198,0.146 1.219,0.146 false 1.958,3.854 2.198,4.177 false 1.698,3.198 1.25,3.552 true 1.781,3.198 2.188,3.563 true 1.26,0.063 2.99,0.24 1.729,0.177 10 false Driver Side Squib 2nd Step 0.771,1.313 1.583,1.51 0.813,0.198 10 false Spiral Cable 1.802,1.677 3.219,1.885 1.417,0.208 10 false Center Airbag Sensor 0.615,2.24 3.01,2.604 2.396,0.365 10 false Front view of wire harness connector: (to Driver Side Squib 2nd Step) 2.25,2.854 3.083,3.104 0.833,0.25 10 false Connector E 0.563,3.271 0.792,3.458 0.229,0.188 10 false z5 2.271,4.125 3.188,4.333 0.917,0.208 10 false Color: Black 0.302,1.01 0.438,1.208 0.135,0.198 10 false F 0.521,1 0.656,1.198 0.135,0.198 10 false E 1.677,0.979 1.813,1.177 0.135,0.198 10 false D 1.792,0.979 1.927,1.177 0.135,0.198 10 false C 2.177,0.99 2.313,1.188 0.135,0.198 10 false B 2.563,0.75 2.698,0.948 0.135,0.198 10 false A 1,3.479 1.25,3.656 0.25,0.177 10 false D2- 2.292,3.521 2.604,3.698 0.313,0.177 10 false D2+

a.

Disconnect the connectors from the center airbag sensor.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
z5-1 (D2-) - Body ground Ignition switch ON Below 1 V
z5-2 (D2+) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
z5-1 (D2-) - z5-2 (D2+) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
z5-1 (D2-) - z5-2 (D2+) Always 1 MΩ or higher
z5-1 (D2-) - Body ground
z5-2 (D2+) - Body ground




OK

4.CHECK CENTER AIRBAG SENSOR

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
4.CHECK CENTER AIRBAG SENSOR
C158846E10
0.323,0.75 0.365,1.781 false 0.167,1.802 1.948,2 1.781,0.198 10 false Driver Side Squib 2nd Step 0.771,1.083 1.604,1.313 0.833,0.229 10 false Spiral Cable 1.833,1.448 3.177,1.698 1.344,0.25 10 false Center Airbag Sensor 0.552,0.833 0.74,1.021 0.188,0.188 10 false E 0.438,0.833 0.625,1.021 0.188,0.188 10 false F 1.75,0.833 1.938,1.021 0.188,0.188 10 false C 1.635,0.833 1.823,1.021 0.188,0.188 10 false D

a.

Connect the connectors to the steering pad and the center airbag sensor.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1810, B1811, B1812 or B1813 is output (for Column Shift Type) A
DTC B1810, B1811, B1812 or B1813 is output (for Floor Shift Type) B
DTC B1810, B1811, B1812 or B1813 is not output C

HINT:

Codes other than DTC B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.




C

A

B

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
U152195E02
1.427,3.292 1,3.719 1,3.719 0.896,3.719 true 1.615,3.281 2.073,3.708 2.073,3.708 2.177,3.708 true 0.281,0.135 0.146,0.135 0.146,0.135 0.146,0.938 false 1.688,0.427 3.125,0.604 1.438,0.177 10 false Instrument Panel Wire 0.323,0.063 2.083,0.229 1.76,0.167 10 false Driver Side Squib 2nd Step 0.594,1.448 1.417,1.635 0.823,0.188 10 false Spiral Cable 1.771,1.823 3.188,2.031 1.417,0.208 10 false Center Airbag Sensor 0.49,2.219 2.885,2.583 2.396,0.365 10 false Rear view of wire harness connector: (to Spiral Cable) 2.323,3.031 3.156,3.281 0.833,0.25 10 false Connector C 0.729,2.917 1.031,3.104 0.302,0.188 10 false J11 0.26,1.167 0.396,1.365 0.135,0.198 10 false F 0.438,1.167 0.573,1.365 0.135,0.198 10 false E 1.5,1.135 1.635,1.333 0.135,0.198 10 false D 1.677,1.146 1.813,1.344 0.135,0.198 10 false C 1.99,1.135 2.125,1.333 0.135,0.198 10 false B 2.344,0.927 2.479,1.125 0.135,0.198 10 false A 0.781,3.635 0.938,3.844 0.156,0.208 10 false 4 2.229,3.604 2.354,3.781 0.125,0.177 10 false 3

a.

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Disconnect the instrument panel wire connector from the spiral cable.


c.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
J11-3 - Body ground Ignition switch ON Below 1 V
J11-4 - Body ground



f.

Turn the ignition switch off.


g.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J11-3 - J11-4 Always Below 1 Ω



i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


j.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J11-3 - J11-4 Always 1 MΩ or higher
J11-3 - Body ground
J11-4 - Body ground




OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE ASSEMBLY