Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1620/21  Driver Side - Side Airbag Sensor Circuit Malfunction  B1625/22  Front Passenger Side - Side Airbag Sensor Circuit Malfunction  


DESCRIPTION

The side airbag sensor LH and RH consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc.

If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.

DTC B1620/21 or B1625/22 is recorded when a malfunction is detected in the side airbag sensor LH or RH circuit.

DTC Code Detection Condition Trouble Area
B1620/21 When one of the following conditions is met:
·

Side airbag sensor LH malfunction

·

Center airbag sensor malfunction


·

Side airbag sensor LH

·

Center airbag sensor assembly


B1625/22 When one of the following conditions is met:
·

Side airbag sensor RH malfunction

·

Center airbag sensor malfunction


·

Side airbag sensor RH

·

Center airbag sensor assembly



WIRING DIAGRAM

C243661E01
5.413,1.69 5.615,1.869 0.202,0.179 10 P1 5.689,0.923 6.112,1.102 0.422,0.179 10 BBD+ 1.564,0.853 1.836,1.007 0.272,0.154 10 2 0.262,1.676 0.534,1.855 0.272,0.179 10 P18 1.564,1.274 1.693,1.432 0.129,0.157 10 1 0.05,0.012 1.248,0.215 1.198,0.203 12 for Driver Side: 5.505,0.853 5.615,1.011 0.110,0.157 10 8 5.689,1.344 6.112,1.523 0.422,0.179 10 BBD- 1.095,0.923 1.489,1.102 0.394,0.179 10 BBL+ 1.095,1.344 1.461,1.523 0.366,0.179 10 BBL- 0.262,1.85 1.722,2.029 1.460,0.179 10 Side Airbag Sensor LH 5.429,1.274 5.614,1.427 0.185,0.153 10 15 5.413,1.859 6.820,2.183 1.407,0.324 10 Center Airbag Sensor Assembly

C243661E02
5.413,1.69 5.615,1.869 0.202,0.179 10 Q1 5.689,0.923 6.112,1.102 0.422,0.179 10 BBP+ 1.564,0.853 1.836,1.007 0.272,0.154 10 2 0.262,1.676 0.559,1.855 0.297,0.179 10 Q14 1.564,1.274 1.836,1.432 0.272,0.157 10 1 0.05,0.012 1.819,0.215 1.769,0.203 12 for Passenger Side: 5.505,0.853 5.615,1.011 0.110,0.157 10 8 5.689,1.344 6.112,1.523 0.422,0.179 10 BBP- 1.095,0.923 1.489,1.102 0.394,0.179 10 BBR+ 1.095,1.344 1.461,1.523 0.366,0.179 10 BBR- 0.262,1.85 1.722,2.029 1.460,0.179 10 Side Airbag Sensor RH 5.429,1.274 5.614,1.427 0.185,0.153 10 11 5.413,1.859 6.820,2.183 1.407,0.324 10 Center Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1620 and B1625 are not output A
DTC B1620 is output B
DTC B1625 is output C



C

2.CHECK CONNECTION OF CONNECTORS

A

B

6.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and side airbag sensor RH.

OK:

The connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and side airbag sensor RH.


b.

Check that the connectors (on the center airbag sensor side and side airbag sensor RH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

4.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR RH)

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR RH)
U152920E02
1.073,0.76 1.219,0.76 1.219,0.76 1.042,1.479 false 3.823,1.438 4.208,1.875 false 3.75,1.438 3.375,1.875 false 5.771,1.719 6.073,2.01 false 5.573,1.583 5.229,2.01 false 6.167,2.333 6.052,2.333 6.052,2.333 5.75,1.938 false 0.031,0.677 1.083,0.885 1.052,0.208 10 false No. 2 Floor Wire 0.052,1.865 0.833,2.208 0.781,0.344 10 false Side Airbag Sensor RH 1.344,1.719 2.26,2.052 0.917,0.333 10 false Center Airbag Sensor 0.479,1.448 0.615,1.594 0.135,0.146 10 false D 1.5,1.448 1.635,1.594 0.135,0.146 10 false A 0.844,1.656 0.979,1.802 0.135,0.146 10 false C 1.146,1.656 1.281,1.802 0.135,0.146 10 false B 2.573,1.302 2.854,1.479 0.281,0.177 10 false Q14 4.865,1.302 5.115,1.479 0.25,0.177 10 false Q1 2.198,0.073 4.51,0.469 2.313,0.396 10 false Rear view of wire harness connector: (to Side Airbag Sensor RH) 4.604,0.073 6.917,0.469 2.313,0.396 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2.26,0.833 3.167,1.031 0.906,0.198 10 false Connector C 4.479,0.896 5.385,1.094 0.906,0.198 10 false Connector B 4.052,1.896 4.448,2.052 0.396,0.156 10 false BBR+ 3.188,1.906 3.583,2.063 0.396,0.156 10 false BBR- 5.042,2.031 5.438,2.188 0.396,0.156 10 false BBP+ 5.958,2.021 6.354,2.177 0.396,0.156 10 false BBP- 6.229,2.271 7.063,2.438 0.833,0.167 10 false Service Wire

a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
Q14-1 (BBR-) - Body ground Ignition switch ON Below 1 V
Q14-2 (BBR+) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Q14-1 (BBR-) - Q14-2 (BBR+) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Q14-1 (BBR-) - Q4-2 (BBR+) Always 1 MΩ or higher
Q14-1 (BBR-) - Body ground
Q14-2 (BBR+) - Body ground




OK

5.CHECK SIDE AIRBAG SENSOR RH

NG

REPLACE NO. 2 FLOOR WIRE

5.CHECK SIDE AIRBAG SENSOR RH
C146230E03
0.548,1.409 1.385,1.739 0.836,0.330 10 Side Airbag Sensor LH 1.76,1.203 2.645,1.539 0.885,0.336 10 Center Airbag Sensor

a.

Interchange the side airbag sensor LH with RH and connect the connectors to them.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1620 and B1625 are not output A
DTC B1620 is output B
DTC B1625 is output (for Column Shift Type) C
DTC B1625 is output (for Floor Shift Type) D

HINT:

Codes other than DTC B1620 and B1625 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


j.

Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.



D

A

B

C

6.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and side airbag sensor LH.

OK:

The connectors are properly connected.




OK

7.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

7.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and side airbag sensor LH.


b.

Check that the connectors (on the center airbag sensor side and side airbag sensor LH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

8.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR LH)

NG

REPLACE FLOOR WIRE

8.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR LH)
U152921E01
0.265,0.418 0.949,0.630 0.684,0.211 10 Floor Wire 0.092,1.603 0.873,1.946 0.781,0.343 10 Side Airbag Sensor LH 1.397,1.663 2.310,2.000 0.913,0.336 10 Center Airbag Sensor 0.509,1.155 0.644,1.297 0.135,0.142 10 D 1.534,1.155 1.669,1.297 0.135,0.142 10 A 0.875,1.358 1.011,1.500 0.135,0.142 10 C 1.186,1.358 1.321,1.500 0.135,0.142 10 B 2.61,1.1 2.887,1.273 0.278,0.173 10 P18 5.274,1.223 5.523,1.396 0.250,0.173 10 P1 2.357,0.052 4.673,0.451 2.316,0.399 10 Rear view of wire harness connector: (to Side Airbag Sensor LH) 4.753,0.052 7.069,0.451 2.316,0.399 10 Rear view of wire harness connector: (to Center Airbag Sensor) 2.364,0.794 3.270,0.996 0.906,0.202 10 Connector C 4.916,0.786 5.822,0.988 0.906,0.202 10 Connector B 4.176,1.811 4.571,1.969 0.394,0.158 10 BBL+ 3.321,1.82 3.715,1.978 0.394,0.158 10 BBL- 3.943,1.337 4.321,1.764 false 3.869,1.337 3.49,1.764 false 5.411,1.81 5.806,1.968 0.394,0.158 10 BBD- 6.473,1.809 6.867,1.967 0.394,0.158 10 BBD+ 6.125,1.375 6.584,1.789 false 5.948,1.502 5.592,1.791 false 5.871,2.035 6.707,2.200 0.836,0.165 10 Service Wire 1.069,1.17 1.069,0.487 1.069,0.487 0.937,0.487 false 6.019,1.798 6.019,2.013 false

a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
P18-1 (BBL-) - Body ground Ignition switch ON Below 1 V
P18-2 (BBL+) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
P18-1 (BBL-) - P18-2 (BBL+) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
P18-1 (BBL-) - P18-2 (BBL+) Always 1 MΩ or higher
P18-1 (BBL-) - Body ground
P18-2 (BBL+) - Body ground




OK

9.CHECK SIDE AIRBAG SENSOR LH

NG

REPLACE FLOOR WIRE

9.CHECK SIDE AIRBAG SENSOR LH
C158841E12
0.771,1.146 1.542,1.479 0.771,0.333 10 false Side Airbag Sensor RH 1.75,1.156 2.677,1.49 0.927,0.333 10 false Center Airbag Sensor

a.

Interchange the side airbag sensor RH with LH and connect the connectors to them.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1620 and B1625 are not output A
DTC B1625 is output B
DTC B1620 is output (for Column Shift Type) C
DTC B1620 is output (for Floor Shift Type) D

HINT:

Codes other than DTC B1620 and B1625 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


j.

Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



D

A

B

C