Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1630/23  Driver Side Rear Airbag Sensor Circuit Malfunction  B1635/24  Front Passenger Side Rear Airbag Sensor Circuit Malfunction  


DESCRIPTION

The side airbag sensor LH and RH consists of the safing sensor, the diagnostic circuit, the lateral deceleration sensor, etc.

If the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.

DTC B1630/23 or B1635/24 is recorded when a malfunction is detected in the side airbag sensor LH or RH circuit.

HINT:

"Rear Airbag Sensor" refers to the side airbag sensor.


DTC Code Detection Condition Trouble Area
B1630/23 When one of the following conditions is met:
·

Side airbag sensor LH malfunction

·

Center airbag sensor malfunction


·

Side airbag sensor LH

·

Center airbag sensor assembly


B1635/24 When one of the following conditions is met:
·

Side airbag sensor RH malfunction

·

Center airbag sensor malfunction


·

Side airbag sensor RH

·

Center airbag sensor assembly



WIRING DIAGRAM

E285818E02
0.135,0.052 1.344,0.271 1.208,0.219 12 false for Driver Side: 1.167,0.927 1.573,1.073 0.406,0.146 10 false BBL+ 1.167,1.76 1.573,1.906 0.406,0.146 10 false BBL- 5.677,0.958 6.083,1.104 0.406,0.146 10 false BBD+ 5.688,1.74 6.094,1.917 0.406,0.177 10 false BBD- 1.167,3.146 1.583,3.333 0.417,0.188 10 false BCL+ 1.167,3.948 1.583,4.135 0.417,0.188 10 false BCL- 3.875,3.146 4.292,3.333 0.417,0.188 10 false BCL+ 3.875,3.958 4.292,4.146 0.417,0.188 10 false BCL- 1.667,0.833 1.823,1.042 0.156,0.208 10 false 4 1.667,1.646 1.781,1.813 0.115,0.167 10 false 3 1.667,3.042 1.833,3.177 0.167,0.135 10 false 1 1.667,3.823 1.823,3.99 0.156,0.167 10 false 2 3.708,3.833 3.927,4.042 0.219,0.208 10 false 1 3.698,3.031 3.906,3.188 0.208,0.156 10 false 2 5.469,0.865 5.688,1.042 0.219,0.177 10 false 8 5.406,1.656 5.635,1.896 0.229,0.24 10 false 15 0.49,4.646 0.729,4.813 0.24,0.167 10 false P4 3.781,4.646 4.073,4.813 0.292,0.167 10 false N11 5.51,4.646 5.781,4.813 0.271,0.167 10 false P1 0.49,4.823 1.969,5.01 1.479,0.188 10 false Side Airbag Sensor LH 3.802,4.802 4.948,5.167 1.146,0.365 10 false Door Side Airbag Sensor LH 5.51,4.823 6.927,5.01 1.417,0.188 10 false Center Airbag Sensor 2.604,3.198 2.896,3.365 0.292,0.167 10 false PN1 2.604,3.958 2.896,4.125 0.292,0.167 10 false PN1 2.708,2.958 2.813,3.125 0.104,0.167 10 false 2 2.688,3.74 2.823,3.948 0.135,0.208 10 false 1

C158884E05
0.129,0 1.660,0.218 1.531,0.218 12 for Passenger Side: 1.159,0.925 1.565,1.067 0.406,0.142 10 BBR+ 1.159,1.757 1.565,1.899 0.406,0.142 10 BBR- 5.672,0.953 6.078,1.095 0.406,0.142 10 BBP+ 5.684,1.735 6.090,1.914 0.406,0.179 10 BBP- 1.159,3.137 1.579,3.320 0.420,0.184 10 BCR+ 1.159,3.94 1.579,4.123 0.420,0.184 10 BCR- 3.87,3.144 4.290,3.327 0.420,0.184 10 BCR+ 3.87,3.947 4.290,4.130 0.420,0.184 10 BCR- 1.659,0.831 1.815,1.042 0.156,0.211 10 4 1.659,1.643 1.773,1.813 0.114,0.170 10 3 1.659,3.03 1.828,3.167 0.170,0.137 10 1 1.663,3.819 1.824,3.984 0.161,0.165 10 2 3.704,3.829 3.922,4.033 0.218,0.205 10 1 3.697,3.025 3.901,3.181 0.205,0.156 10 2 5.463,0.861 5.677,1.038 0.215,0.177 10 8 5.397,1.653 5.622,1.892 0.225,0.239 10 11 0.486,4.637 0.726,4.806 0.239,0.170 10 Q4 3.779,4.637 4.067,4.799 0.288,0.163 10 M9 5.502,4.637 5.776,4.806 0.274,0.170 10 Q1 0.486,4.812 1.969,4.995 1.482,0.184 10 Side Airbag Sensor RH 3.793,4.8 4.939,5.163 1.145,0.363 10 Door Side Airbag Sensor RH 5.502,4.812 6.922,4.995 1.420,0.184 10 Center Airbag Sensor 2.583,3.923 2.961,4.088 0.378,0.165 10 MQ1 2.707,2.944 2.812,3.109 0.105,0.165 10 2 2.69,3.735 2.825,3.940 0.135,0.205 10 1 2.589,3.143 2.967,3.308 0.378,0.165 10 MQ1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1630 and B1635 are not output A
DTC B1630 is output B
DTC B1635 is output C



C

2.CHECK CONNECTION OF CONNECTORS

A

B

12.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and side airbag sensor RH.

OK:

The connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and side airbag sensor RH.


b.

Check that the connectors (on the center airbag sensor side and side airbag sensor RH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

4.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR RH)

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR RH)
U152922E02
1.104,0.781 1.24,0.781 1.24,0.781 1.073,1.49 false 3.698,1.438 4.083,1.875 false 3.563,1.427 3.177,1.854 false 5.792,1.708 6.104,2 false 5.604,1.573 5.26,2 false 6.198,2.323 6.073,2.323 6.073,2.323 5.771,1.938 false 0.063,0.708 1.115,0.917 1.052,0.208 10 false No. 2 Floor Wire 0.083,1.854 0.865,2.198 0.781,0.344 10 false Side Airbag Sensor RH 1.375,1.719 2.292,2.052 0.917,0.333 10 false Center Airbag Sensor 0.5,1.448 0.635,1.594 0.135,0.146 10 false D 1.531,1.479 1.667,1.625 0.135,0.146 10 false A 0.865,1.677 1,1.823 0.135,0.146 10 false C 1.177,1.688 1.313,1.833 0.135,0.146 10 false B 2.5,1.167 2.75,1.344 0.25,0.177 10 false Q4 4.885,1.292 5.135,1.469 0.25,0.177 10 false Q1 2.229,0.042 4.542,0.438 2.313,0.396 10 false Rear view of wire harness connector: (to Side Airbag Sensor RH) 4.625,0.042 6.938,0.438 2.313,0.396 10 false Rear view of wire harness connector: (to Center Airbag Sensor) 2.229,0.771 3.135,0.969 0.906,0.198 10 false Connector C 4.396,0.948 5.302,1.146 0.906,0.198 10 false Connector B 3.906,1.927 4.302,2.083 0.396,0.156 10 false BBR+ 3.021,1.896 3.417,2.052 0.396,0.156 10 false BBR- 5.073,2.021 5.469,2.177 0.396,0.156 10 false BBP+ 5.979,2.021 6.375,2.177 0.396,0.156 10 false BBP- 6.26,2.26 7.094,2.427 0.833,0.167 10 false Service Wire

a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
Q4-3 (BBR-) - Body ground Ignition switch ON Below 1 V
Q4-4 (BBR+) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 8 (BBP+) and 11 (BBP-) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Q4-3 (BBR-) - Q4-4 (BBR+) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Q4-3 (BBR-) - Q4-4 (BBR+) Always 1 MΩ or higher
Q4-3 (BBR-) - Body ground
Q4-4 (BBR+) - Body ground




OK

5.CHECK SIDE AIRBAG SENSOR RH

NG

REPLACE NO. 2 FLOOR WIRE

5.CHECK SIDE AIRBAG SENSOR RH
C146230E03
0.548,1.409 1.385,1.739 0.836,0.330 10 Side Airbag Sensor LH 1.76,1.203 2.645,1.539 0.885,0.336 10 Center Airbag Sensor

a.

Interchange the side airbag sensor LH with RH and connect the connectors to them.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1630 and B1635 are not output A
DTC B1630 is output (for Double Cab) B
DTC B1630 is output (for CrewMax) C
DTC B1635 is output D

HINT:

Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


j.

Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.



D

6.CHECK CONNECTION OF CONNECTORS

A

B

C

6.CHECK CONNECTION OF CONNECTORS
a.

Check that the connector is properly connected to the door side airbag sensor RH.

OK:

The connector is properly connected.




OK

7.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

7.CHECK CONNECTORS
a.

Disconnect the connectors from the side airbag sensor RH and door side airbag sensor RH.


b.

Check that the connector (on the door side airbag sensor RH side) is not damaged.

OK:

The connector is not deformed or damaged.




OK

8.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

8.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT
U152923E01
1.733,1.054 1.903,1.224 0.170,0.170 10 A 1.444,1.227 1.614,1.397 0.170,0.170 10 B 1.222,1.227 1.392,1.397 0.170,0.170 10 C 1.09,1.227 1.259,1.397 0.170,0.170 10 D 0.863,1.227 1.032,1.397 0.170,0.170 10 E 0.557,1.054 0.727,1.224 0.170,0.170 10 F 0.017,1.529 1.145,1.893 1.128,0.364 10 Door Side Airbag Sensor RH 1.542,1.529 2.309,1.893 0.767,0.364 10 Side Airbag Sensor RH 2.265,0.099 4.643,0.428 2.378,0.330 10 Front view of wire harness connector: (to Door Side Airbag Sensor RH) 4.721,0.099 7.065,0.428 2.343,0.330 10 Rear view of wire harness connector: (to Side Airbag Sensor RH) 2.369,0.971 3.205,1.148 0.836,0.177 10 Connector E 4.276,0.99 5.113,1.166 0.836,0.177 10 Connector B 2.607,1.41 2.888,1.611 0.281,0.201 10 M9 4.517,1.457 4.798,1.658 0.281,0.201 10 Q4 2.889,2.248 3.327,2.463 0.437,0.215 10 BCR- 3.824,2.248 4.261,2.463 0.437,0.215 10 BCR+ 3.611,1.653 3.999,2.248 false 3.443,1.653 3.055,2.248 false 5.904,2.178 6.341,2.393 0.437,0.215 10 BCR- 4.886,2.159 5.323,2.374 0.437,0.215 10 BCR+ 5.612,1.637 6.079,2.113 false 5.519,1.637 5.052,2.113 false 5.563,1.998 5.372,2.455 false 4.888,2.473 5.711,2.628 0.823,0.156 10 Service Wire

a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
M9-1 (BCR-) - Body ground Ignition switch ON Below 1 V
M9-2 (BCR+) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
M9-1 (BCR-) - M9-2 (BCR+) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
M9-1 (BCR-) - M9-2 (BCR+) Always 1 MΩ or higher
M9-1 (BCR-) - Body ground
M9-2 (BCR+) - Body ground




OK

9.CHECK FOR DTC

NG

11.CHECK NO. 2 FLOOR WIRE
9.CHECK FOR DTC
a.
C167367E01
0.32,1.273 1.504,1.596 1.183,0.323 10 Door Side Airbag Sensor RH 2.002,1.283 2.825,1.605 0.822,0.323 10 Side Airbag Sensor RH

Connect the connectors to the side airbag sensor RH.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1635 is output.


HINT:

Codes other than B1635 may be output at this time, but they are not related to this check.


Result
Result Proceed to
NG (for Double Cab) A
NG (for CrewMax) B
OK C



C

10.CHECK SIDE AIRBAG SENSOR RH

A

B

10.CHECK SIDE AIRBAG SENSOR RH
C146230E03
0.548,1.409 1.385,1.739 0.836,0.330 10 Side Airbag Sensor LH 1.76,1.203 2.645,1.539 0.885,0.336 10 Center Airbag Sensor

a.

Interchange the side airbag sensor LH with RH and connect the connectors to them.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1630 and B1635 are not output A
DTC B1635 is output (for Column Shift Type) B
DTC B1635 is output (for Floor Shift Type) C
DTC B1630 is output (for Double Cab) D
DTC B1630 is output (for CrewMax) E

HINT:

Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


j.

Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.



E

A

B

C

D

11.CHECK NO. 2 FLOOR WIRE
U152925E02
0.948,0.417 1.042,0.417 1.042,0.417 1.042,1.094 false 1.448,1.094 1.448,0.156 1.448,0.156 1.281,0.156 false 3.844,1.656 4.208,2.333 false 3.5,1.656 3.125,2.333 false 5.667,1.802 6.156,2.271 false 5.563,1.802 5.073,2.271 false 5.635,2.125 5.521,2.479 false 0.167,0.042 1.25,0.198 1.083,0.156 10 false No. 2 Floor Wire 0.052,0.323 0.979,0.479 0.927,0.156 10 false Door Wire RH 0.042,1.479 1.135,1.813 1.094,0.333 10 false Door Side Airbag Sensor RH 1.635,1.479 2.396,1.813 0.76,0.333 10 false Side Airbag Sensor RH 1.813,1.052 1.969,1.208 0.156,0.156 10 false A 1.542,1.229 1.698,1.385 0.156,0.156 10 false B 1.281,1.229 1.438,1.385 0.156,0.156 10 false C 1.125,1.229 1.281,1.385 0.156,0.156 10 false D 0.854,1.229 1.01,1.385 0.156,0.156 10 false E 0.604,1.052 0.76,1.208 0.156,0.156 10 false F 4.76,0.094 7.104,0.479 2.344,0.385 10 false Rear view of wire harness connector: (to Side Airbag Sensor) 2.344,0.094 4.688,0.479 2.344,0.385 10 false Front view of wire harness connector: (to Door Wire RH) 2.719,1.479 3.052,1.667 0.333,0.188 10 false MQ1 4.656,1.625 4.99,1.813 0.333,0.188 10 false Q4 2.417,0.844 3.333,1.073 0.917,0.229 10 false Connector C 4.229,1.042 5.146,1.271 0.917,0.229 10 false Connector B 2.969,2.344 3.385,2.552 0.417,0.208 10 false BCR+ 4.917,2.302 5.333,2.51 0.417,0.208 10 false BCR+ 4.083,2.344 4.5,2.552 0.417,0.208 10 false BCR- 6,2.313 6.417,2.521 0.417,0.208 10 false BCR- 5.031,2.5 5.854,2.656 0.823,0.156 10 false Service Wire

a.

Disconnect the No. 2 floor wire connector from the door wire RH.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
MQ1-1 (BCR-) - Body ground Ignition switch ON Below 1 V
MQ1-2 (BCR+) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 1 (BCR+) and 2 (BCR-) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
MQ1-1 (BCR-) - MQ1-2 (BCR+) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
MQ1-1 (BCR-) - MQ1-2 (BCR+) Always 1 MΩ or higher
MQ1-1 (BCR-) - Body ground
MQ1-2 (BCR+) - Body ground




OK

REPLACE DOOR WIRE RH

NG

REPLACE NO. 2 FLOOR WIRE

12.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and side airbag sensor LH.

OK:

The connectors are properly connected.




OK

13.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

13.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and side airbag sensor LH.


b.

Check that the connectors (on the center airbag sensor side and side airbag sensor LH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

14.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR LH)

NG

REPLACE FLOOR WIRE

14.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - SIDE AIRBAG SENSOR LH)
U152926E01
0.347,0.43 1.030,0.641 0.684,0.211 10 Floor Wire 0.174,1.614 0.955,1.958 0.781,0.343 10 Side Airbag Sensor LH 1.478,1.675 2.391,2.011 0.913,0.336 10 Center Airbag Sensor 0.591,1.167 0.726,1.309 0.135,0.142 10 D 1.616,1.167 1.751,1.309 0.135,0.142 10 A 0.957,1.37 1.092,1.512 0.135,0.142 10 C 1.267,1.37 1.402,1.512 0.135,0.142 10 B 2.82,1.331 3.070,1.505 0.250,0.173 10 P4 5.066,1.57 5.315,1.743 0.250,0.173 10 P1 2.39,0.045 4.705,0.444 2.316,0.399 10 Rear view of wire harness connector: (to Side Airbag Sensor LH) 4.786,0.045 7.101,0.444 2.316,0.399 10 Rear view of wire harness connector: (to Center Airbag Sensor) 2.488,0.934 3.394,1.137 0.906,0.202 10 Connector C 4.704,1.074 5.610,1.277 0.906,0.202 10 Connector B 4.274,2.145 4.669,2.303 0.394,0.158 10 BBL+ 3.449,2.138 3.843,2.296 0.394,0.158 10 BBL- 4.057,1.671 4.436,2.098 false 3.983,1.671 3.604,2.098 false 5.164,2.231 5.558,2.389 0.394,0.158 10 BBD- 6.225,2.23 6.619,2.388 0.394,0.158 10 BBD+ 5.878,1.796 6.336,2.21 false 5.701,1.924 5.345,2.213 false 5.623,2.456 6.460,2.622 0.836,0.165 10 Service Wire 1.15,1.181 1.15,0.499 1.15,0.499 1.019,0.499 false 5.771,2.22 5.771,2.435 false

a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
P4-3 (BBL-) - Body ground Ignition switch ON Below 1 V
P4-4 (BBL+) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 8 (BBD+) and 15 (BBD-) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
P4-3 (BBL-) - P4-4 (BBL+) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
P4-3 (BBL-) - P4-4 (BBL+) Always 1 MΩ or higher
P4-3 (BBL-) - Body ground
P4-4 (BBL+) - Body ground




OK

15.CHECK SIDE AIRBAG SENSOR LH

NG

REPLACE FLOOR WIRE

15.CHECK SIDE AIRBAG SENSOR LH
C158841E13
0.76,1.146 1.531,1.479 0.771,0.333 10 false Side Airbag Sensor RH 1.729,1.167 2.656,1.5 0.927,0.333 10 false Center Airbag Sensor

a.

Interchange the side airbag sensor RH with LH and connect the connectors to them.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1630 and B1635 are not output A
DTC B1635 is output (for Double Cab) B
DTC B1635 is output (for CrewMax) C
DTC B1630 is output D

HINT:

Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


j.

Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



D

16.CHECK NO. 2 FLOOR WIRE (SIDE AIRBAG SENSOR LH - DOOR SIDE AIRBAG SENSOR LH)

A

B

C

16.CHECK NO. 2 FLOOR WIRE (SIDE AIRBAG SENSOR LH - DOOR SIDE AIRBAG SENSOR LH)
U152924E01
1.733,1.054 1.903,1.224 0.170,0.170 10 A 1.444,1.227 1.614,1.397 0.170,0.170 10 B 1.222,1.227 1.392,1.397 0.170,0.170 10 C 1.09,1.227 1.259,1.397 0.170,0.170 10 D 0.863,1.227 1.032,1.397 0.170,0.170 10 E 0.557,1.054 0.727,1.224 0.170,0.170 10 F 0.017,1.529 1.145,1.893 1.128,0.364 10 Door Side Airbag Sensor LH 1.542,1.529 2.309,1.893 0.767,0.364 10 Side Airbag Sensor LH 2.265,0.099 4.643,0.428 2.378,0.330 10 Front view of wire harness connector: (to Door Side Airbag Sensor LH) 4.721,0.099 7.065,0.428 2.343,0.330 10 Rear view of wire harness connector: (to Side Airbag Sensor LH) 2.369,0.971 3.205,1.148 0.836,0.177 10 Connector E 4.276,0.99 5.113,1.166 0.836,0.177 10 Connector B 2.579,1.41 2.860,1.611 0.281,0.201 10 N11 4.517,1.457 4.798,1.658 0.281,0.201 10 P4 2.889,2.248 3.327,2.463 0.437,0.215 10 BCL- 3.824,2.248 4.261,2.463 0.437,0.215 10 BCL+ 3.611,1.653 3.999,2.248 false 3.443,1.653 3.055,2.248 false 5.904,2.178 6.341,2.393 0.437,0.215 10 BCL- 4.886,2.159 5.323,2.374 0.437,0.215 10 BCL+ 5.612,1.637 6.079,2.113 false 5.519,1.637 5.052,2.113 false 5.59,2.014 5.487,2.363 false 5.004,2.38 5.827,2.536 0.823,0.156 10 Service Wire

a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
N11-1 (BCL-) - Body ground Ignition switch ON Below 1 V
N11-2 (BCL+) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 2 (BCL-) and 1 (BCL+) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
N11-1 (BCL-) - N11-2 (BCL+) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
N11-1 (BCL-) - N11-2 (BCL+) Always 1 MΩ or higher
N11-1 (BCL-) - Body ground
N11-2 (BCL+) - Body ground




OK

17.CHECK FOR DTC

NG

19.CHECK FLOOR WIRE
17.CHECK FOR DTC
a.
C167367E02
0.343,1.235 1.508,1.603 1.165,0.369 10 Door Side Airbag Sensor LH 1.993,1.235 2.895,1.603 0.902,0.369 10 Side Airbag Sensor LH

Connect the connectors to the side airbag sensor LH.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1630 is output.


HINT:

Codes other than B1630 may be output at this time, but they are not related to this check.


Result
Result Proceed to
NG (for Double Cab) A
NG (for CrewMax) B
OK C



C

18.CHECK SIDE AIRBAG SENSOR LH

A

B

18.CHECK SIDE AIRBAG SENSOR LH
C158841E14
0.823,1.135 1.594,1.469 0.771,0.333 10 false Side Airbag Sensor RH 1.771,1.167 2.698,1.5 0.927,0.333 10 false Center Airbag Sensor

a.

Interchange the side airbag sensor RH with LH and connect the connectors to them.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1630 and B1635 are not output A
DTC B1630 is output (for Column Shift Type) B
DTC B1630 is output (for Floor Shift Type) C
DTC B1635 is output (for Double Cab) D
DTC B1635 is output (for CrewMax) E

HINT:

Codes other than DTC B1630 and B1635 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


j.

Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



E

A

B

C

D

19.CHECK FLOOR WIRE
U152927E01
0.562,0.058 1.644,0.214 1.082,0.156 10 Floor Wire 0.061,0.333 0.986,0.489 0.924,0.156 10 Door Wire LH 0.953,0.403 1.053,0.403 1.053,0.403 1.053,1.078 false 1.463,1.078 1.463,0.144 1.463,0.144 1.278,0.144 false 0.054,1.485 1.150,1.814 1.097,0.330 10 Door Side Airbag Sensor LH 1.642,1.485 2.412,1.814 0.770,0.330 10 Side Airbag Sensor LH 1.82,1.053 1.977,1.209 0.156,0.156 10 A 1.551,1.238 1.707,1.394 0.156,0.156 10 B 1.286,1.238 1.442,1.394 0.156,0.156 10 C 1.136,1.238 1.292,1.394 0.156,0.156 10 D 0.866,1.238 1.022,1.394 0.156,0.156 10 E 0.612,1.053 0.768,1.209 0.156,0.156 10 F 4.808,0.072 7.152,0.457 2.343,0.385 10 Rear view of wire harness connector: (to Side Airbag Sensor) 2.391,0.072 4.734,0.457 2.343,0.385 10 Front view of wire harness connector: (to Door Wire LH) 2.809,1.362 3.144,1.548 0.335,0.185 10 PN1 4.743,1.538 5.078,1.723 0.335,0.185 10 P4 2.459,0.896 3.371,1.122 0.913,0.225 10 Connector C 4.329,1.001 5.242,1.227 0.913,0.225 10 Connector B 4.073,2.38 4.492,2.591 0.420,0.211 10 BCL+ 5.922,2.238 6.342,2.449 0.420,0.211 10 BCL- 2.971,2.38 3.391,2.591 0.420,0.211 10 BCL- 4.807,2.238 5.226,2.449 0.420,0.211 10 BCL+ 3.744,1.924 4.222,2.337 false 3.513,1.917 3.136,2.337 false 5.589,1.755 6.08,2.233 false 5.488,1.755 4.997,2.233 false 5.537,2.019 5.346,2.476 false 4.863,2.493 5.685,2.649 0.823,0.156 10 Service Wire

a.

Disconnect the floor wire connector from the door wire LH.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
PN1-1 (BCL-) - Body ground Ignition switch ON Below 1 V
PN1-2 (BCL+) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 1 (BCL+) and 2 (BCL-) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
PN1-1 (BCL-) - PN1-2 (BCL+) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
PN1-1 (BCL-) - PN1-2 (BCL+) Always 1 MΩ or higher
PN1-1 (BCL-) - Body ground
PN1-2 (BCL+) - Body ground




OK

REPLACE DOOR WIRE LH

NG

REPLACE FLOOR WIRE