Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234205 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1782  Rear Occupant Classification Sensor LH Circuit Malfunction  


DESCRIPTION

The rear occupant detection sensor LH circuit consists of the occupant classification ECU and the rear occupant detection sensor LH.

DTC B1782 is set when a malfunction is detected in the rear occupant detection sensor LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1782 One of following conditions is met:
·

Occupant classification ECU receives line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in rear occupant detection sensor LH circuit for 2 seconds

·

Rear occupant detection sensor LH malfunction

·

Occupant classification ECU malfunction


·

Front seat frame with adjuster RH (Rear occupant detection sensor LH)

·

Front seat wire RH

·

Occupant classification ECU



HINT:
·

When DTC B1650/32 is detected as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1782 of the occupant classification system.

·

Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.



WIRING DIAGRAM

B151586E48
1.577,1.701 1.733,1.882 0.156,0.181 10 2 1.577,0.389 1.733,0.570 0.156,0.181 10 1 1.577,3.036 1.733,3.217 0.156,0.181 10 3 5.532,0.392 5.703,0.574 0.171,0.181 10 5 5.218,3.796 5.508,3.977 0.290,0.181 10 Y1 5.532,1.694 5.688,1.876 0.156,0.181 10 9 5.494,3.028 5.699,3.209 0.205,0.181 10 3 5.732,0.471 6.143,0.652 0.411,0.181 10 SVC3 5.732,1.798 6.087,1.979 0.355,0.181 10 SIG3 5.732,3.127 6.169,3.308 0.438,0.181 10 SGD3 1.165,0.471 1.577,0.652 0.411,0.181 10 SVC 1.189,1.798 1.544,1.979 0.355,0.181 10 SIG 1.149,3.127 1.587,3.308 0.438,0.181 10 SGD 0.136,3.964 2.525,4.164 2.390,0.200 10 Rear Occupant Detection Sensor LH 5.229,3.964 7.029,4.145 1.800,0.181 10 Occupant Classification ECU 0.136,3.796 0.453,3.977 0.317,0.181 10 Y6

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

If troubleshooting (wire harness inspection) is difficult to perform, remove the front seat RH installation bolts to see the undersurface of the seat cushion.

·

In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear any DTCs stored in the memory (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Using the Techstream, check for DTCs of the occupant classification ECU (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1782 is not output.


HINT:

DTCs other than DTC B1782 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the occupant classification ECU and the rear occupant detection sensor LH.

OK:

Connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS

3.CHECK CONNECTORS
a.

Check that the connectors (on the occupant classification ECU side and rear occupant detection sensor LH side) are not damaged (see page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

OK:

Connectors are not deformed or damaged.




OK

4.CHECK FRONT SEAT WIRE RH

NG

REPLACE FRONT SEAT WIRE RH

4.CHECK FRONT SEAT WIRE RH
U152917E02
1.146,1.479 1.354,0.708 1.354,0.708 1.25,0.708 false 3.448,1.438 3.135,1.177 false 5.938,1.323 5.521,0.906 false 5.948,1.479 5.51,1.719 false 3.552,1.49 3.552,1.896 true 3.677,1.479 4.104,1.76 false 6.188,1.333 6.615,1.156 false 3.281,1.833 3.146,2.125 false 3.323,1.083 3.115,0.865 false 1.479,1.75 2.333,2.271 0.854,0.521 10 false Occupant Classification ECU 2.198,0.01 4.781,0.417 2.583,0.406 10 false Front view of wire harness connector: (to Rear Occupant Detection Sensor LH) 4.813,0 7.156,0.406 2.344,0.406 10 false Front view of wire harness connector: (to Occupant Classification ECU) 3.969,0.75 4.802,0.948 0.833,0.198 10 false Connector C 2.333,2.031 3.167,2.229 0.833,0.198 10 false Service Wire 2.802,1.094 3.208,1.292 0.406,0.198 10 false SVC 2.677,1.396 2.906,1.573 0.229,0.177 10 false Y6 5.063,1.219 5.292,1.396 0.229,0.177 10 false Y1 3.427,1.917 3.833,2.115 0.406,0.198 10 false SIG 3.99,1.729 4.396,1.927 0.406,0.198 10 false SGD 6.323,0.75 7.135,0.948 0.813,0.198 10 false Connector B 0.042,1.823 1.073,2.333 1.031,0.51 10 false Rear Occupant Detection Sensor LH 0.49,1.438 0.646,1.604 0.156,0.167 10 false D 1.615,1.469 1.771,1.635 0.156,0.167 10 false A 0.021,0.646 1.26,0.99 1.24,0.344 10 false Front Seat Wire RH 1.302,1.656 1.448,1.823 0.146,0.167 10 false B 0.823,1.667 0.958,1.833 0.135,0.167 10 false C 5.094,0.781 5.542,0.979 0.448,0.198 10 false SGD3 5.156,1.656 5.521,1.854 0.365,0.198 10 false SIG3 6.635,1.073 7.042,1.271 0.406,0.198 10 false SVC3 2.333,0.802 3.167,1 0.833,0.198 10 false Service Wire

a.

Disconnect the connectors from the occupant classification ECU and the rear occupant detection sensor LH.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
Y1-3 (SGD3) - Body ground Ignition switch ON Below 1 V
Y1-5 (SVC3) - Body ground
Y1-9 (SIG3) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


g.

Using service wires, connect terminals 1 (SVC) and 3 (SGD), and connect terminals 2 (SIG) and 3 (SGD) of connector C.

NOTICE:

Do not forcibly insert the service wires into the terminals of the connector.



h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Y1-5 (SVC3) - Y1-3 (SGD3) Always Below 1 Ω
Y1-9 (SIG3) - Y1-3 (SGD3)



i.

Disconnect the service wires from connector C.


j.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Y1-5 (SVC3) - Y1-3 (SGD3) Always 1 MΩ or higher
Y1-9 (SIG3) - Y1-3 (SGD3)
Y1-5 (SVC3) - Y1-9 (SIG3)
Y1-3 (SGD3) - Body ground
Y1-5 (SVC3) - Body ground
Y1-9 (SIG3) - Body ground




OK

5.CHECK FOR DTC

NG

REPLACE FRONT SEAT WIRE RH

5.CHECK FOR DTC
a.

Connect the connectors to the occupant classification ECU and the rear occupant detection sensor LH.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear any DTCs stored in the memory (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Using the Techstream, check for DTCs of the occupant classification ECU (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1782 is not output.


HINT:

DTCs other than DTC B1782 may be output at this time, but they are not related to this check.




OK

NG

6.REPLACE OCCUPANT CLASSIFICATION ECU
6.REPLACE OCCUPANT CLASSIFICATION ECU
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Replace the occupant classification ECU.


HINT:

Perform the inspection using parts from a normal vehicle when possible.




NEXT

7.PERFORM ZERO POINT CALIBRATION
7.PERFORM ZERO POINT CALIBRATION
a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



OK

8.PERFORM SENSITIVITY CHECK

NG

10.REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH
8.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




OK

9.CHECK FOR DTC

NG

10.REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH
9.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear the DTCs stored in the memory (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Using the Techstream, check for DTCs of the occupant classification ECU (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1782 is not output.


HINT:

DTCs other than DTC B1782 may be output at this time, but they are not related to this check.




OK

END

NG

10.REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH
10.REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Replace the front seat frame with adjuster RH (see page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>REMOVAL).

HINT:

Perform the inspection using parts from a normal vehicle when possible.




NEXT

11.PERFORM ZERO POINT CALIBRATION
11.PERFORM ZERO POINT CALIBRATION
a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

12.PERFORM SENSITIVITY CHECK
12.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




NEXT

END