Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234205 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1785  Front Occupant Classification Sensor LH Collision Detection  


DESCRIPTION

DTC B1785 is set when the occupant classification ECU receives a collision detection signal, which is sent by the front occupant detection sensor LH when an accident occurs.

DTC B1785 is also set when the front seat frame with adjuster RH is subjected to a strong impact, even if an actual accident has not occurred.

However, when the occupant classification ECU outputs a collision detection signal, even if the vehicle is not in a collision, DTC B1785 can be cleared by conducting the zero point calibration and sensitivity check.

Therefore, if DTC B1785 is set, first perform the zero point calibration and sensitivity check.

DTC Code DTC Detection Condition Trouble Area
B1785 Either of following conditions is met:
·

Occupant classification ECU receives collision detection signal, which is sent by front occupant detection sensor LH when accident occurs

·

Front seat frame with adjuster RH is subjected to strong impact, even if actual accident has not occurred


·

Front seat frame with adjuster RH (Front occupant detection sensor LH)

·

Occupant classification ECU



HINT:
·

When DTC B1650/32 is set as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1785 of the occupant classification system.

·

Use the Techstream to check for DTCs of the occupant classification ECU, otherwise the DTCs cannot be read.



WIRING DIAGRAM

B151586E46
1.577,1.701 1.733,1.882 0.156,0.181 10 2 1.577,0.389 1.733,0.570 0.156,0.181 10 1 1.577,3.036 1.733,3.217 0.156,0.181 10 3 5.466,0.392 5.685,0.618 0.219,0.225 10 11 5.218,3.796 5.508,3.977 0.290,0.181 10 Y1 5.532,1.694 5.688,1.876 0.156,0.181 10 7 5.532,3.028 5.736,3.209 0.205,0.181 10 1 5.732,0.471 6.143,0.652 0.411,0.181 10 SVC1 5.732,1.798 6.087,1.979 0.355,0.181 10 SIG1 5.732,3.127 6.169,3.308 0.438,0.181 10 SGD1 1.165,0.471 1.577,0.652 0.411,0.181 10 SVC 1.189,1.798 1.544,1.979 0.355,0.181 10 SIG 1.149,3.127 1.587,3.308 0.438,0.181 10 SGD 0.136,3.964 2.550,4.164 2.414,0.200 10 Front Occupant Detection Sensor LH 5.229,3.964 7.029,4.145 1.800,0.181 10 Occupant Classification ECU 0.136,3.796 0.453,3.977 0.317,0.181 10 Y4

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear any DTCs stored in the center airbag sensor (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).


c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Using the Techstream, check for DTCs of the occupant classification ECU (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1785 is not output.


HINT:

DTCs other than DTC B1785 may be output at this time, but they are not related to this check.




OK

NG

2.PERFORM ZERO POINT CALIBRATION
2.PERFORM ZERO POINT CALIBRATION
a.

Using the Techstream, perform the zero point calibration (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



OK

3.PERFORM SENSITIVITY CHECK

NG

5.REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH
3.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




OK

4.CHECK FOR DTC

NG

5.REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH
4.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear any DTCs stored in the center airbag sensor (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).


c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Using the Techstream, check for DTCs of the occupant classification ECU (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1785 is not output.


HINT:

DTCs other than DTC B1785 may be output at this time, but they are not related to this check.




OK

END

NG

5.REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH
5.REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Replace the front seat frame with adjuster RH (see page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>REMOVAL).

HINT:

Perform the inspection using parts from a normal vehicle when possible.




NEXT

6.PERFORM ZERO POINT CALIBRATION
6.PERFORM ZERO POINT CALIBRATION
a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



OK

7.PERFORM SENSITIVITY CHECK

NG

9.REPLACE OCCUPANT CLASSIFICATION ECU
7.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




OK

8.CHECK FOR DTC

NG

9.REPLACE OCCUPANT CLASSIFICATION ECU
8.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear any DTCs stored in the memory (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

HINT:
·

First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor.

·

Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.




c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Using the Techstream, check for DTCs of the occupant classification ECU (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1785 is not output.


HINT:

DTCs other than DTC B1785 may be output at this time, but they are not related to this check.




OK

END

NG

9.REPLACE OCCUPANT CLASSIFICATION ECU
9.REPLACE OCCUPANT CLASSIFICATION ECU
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Replace the occupant classification ECU.


HINT:

Perform the inspection using parts from a normal vehicle when possible.




NEXT

10.PERFORM ZERO POINT CALIBRATION
10.PERFORM ZERO POINT CALIBRATION
a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

11.PERFORM SENSITIVITY CHECK
11.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




NEXT

END