Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234205 OCCUPANT CLASSIFICATION SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  Trouble in Passenger Airbag ON/OFF Indicator  


DESCRIPTION

The passenger airbag ON/OFF indicator consists of the center airbag sensor assembly, occupant detection ECU, hazard warning switch assembly, and 4 occupant classification sensors. This system controls the passenger airbag deployment according to the occupancy condition of the front passenger seat, and also displays those detected conditions.

WIRING DIAGRAM

E285768E02
1.531,2.146 1.76,2.344 0.229,0.198 10 false 9 1,3.01 1.438,3.208 0.438,0.198 10 false BGND 1.063,2.281 1.448,2.479 0.385,0.198 10 false BSW 1.542,1.063 1.771,1.26 0.229,0.198 10 false 4 1.063,1.167 1.448,1.365 0.385,0.198 10 false FSR- 1.542,0.656 1.771,0.854 0.229,0.198 10 false 8 1.063,0.76 1.448,0.958 0.385,0.198 10 false FSR+ 5.906,1.208 6.292,1.406 0.385,0.198 10 false FSP- 5.906,0.781 6.292,0.979 0.385,0.198 10 false FSP+ 5.656,1.063 5.885,1.26 0.229,0.198 10 false 13 5.604,1.5 5.854,1.698 0.25,0.198 10 false Q1 5.656,0.656 5.885,0.854 0.229,0.198 10 false 12 1.521,2.885 1.75,3.083 0.229,0.198 10 false 5 0.052,3.51 0.302,3.708 0.25,0.198 10 false Y2 3.177,3.594 3.427,3.792 0.25,0.198 10 false Y3 3.01,2.146 3.26,2.344 0.25,0.198 10 false 1 3.021,2.885 3.271,3.083 0.25,0.198 10 false 2 3.208,3.125 3.604,3.323 0.396,0.198 10 false RBE- 3.198,2.135 3.656,2.333 0.458,0.198 10 false RBE+ 3.177,3.813 5.229,4.292 2.052,0.479 10 false Front Seat Inner Belt RH (Passenger Side Buckle Switch) 0.042,3.698 1.896,3.906 1.854,0.208 10 false Occupant Classification ECU 5.615,1.688 7.01,1.896 1.396,0.208 10 false Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT
a.

Turn the ignition switch off.


b.

Loosen the 4 installation bolts of the front seat RH.


c.

Tighten the 4 installation bolts of the front seat RH to the specified torque.



Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


NEXT

2.PERFORM ZERO POINT CALIBRATION
2.PERFORM ZERO POINT CALIBRATION
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Using the Techstream, perform the zero point calibration (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

OK:

Zero point calibration is completed using tester.




OK

END

NG

3.READ VALUE USING TECHSTREAM (PASSENGER SIDE BUCKLE SWITCH)
3.READ VALUE USING TECHSTREAM (PASSENGER SIDE BUCKLE SWITCH)
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Using the Techstream, read the "Data List" (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST).

Occupant Detection:
Tester Display Measure Item / Range Normal Condition Diagnostic Note
Passenger Buckle SW Passenger side buckle switch / Set, Unset or NG Set: Passenger side seat belt is fastened
Unset: Passenger side seat belt is unfastened
NG: Passenger side seat belt is malfunctioning
-

OK:

Display changed correctly according to operation of buckle switch.




OK

4.READ VALUE USING TECHSTREAM (OCCUPANT DETECTION SENSOR)

NG

8.CHECK CONNECTORS
4.READ VALUE USING TECHSTREAM (OCCUPANT DETECTION SENSOR)
a.

Fasten the passenger side seat belt.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Using the Techstream, read the "Data List" (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DATA LIST / ACTIVE TEST).

Occupant Detection:
Tester Display Test Part Control Range Diagnostic Note
FL Sensor Voltage Front left sensor voltage/
Min.: 0 V
Max.: 19.8 V
0 to 4.7 V -
FR Sensor Voltage Front right sensor voltage/
Min.: 0 V
Max.: 19.8 V
0 to 4.7 V -
RL Sensor Voltage Rear left sensor voltage/
Min.: 0 V
Max.: 19.8 V
0 to 4.7 V -
RR Sensor Voltage Rear right sensor voltage/
Min.: 0 V
Max.: 19.8 V
0 to 4.7 V -
FL Sensor Weight Info Front left sensor weight information/
Min.: -17 kg (-37.48 lb)
Max.: 27 kg (59.52 lb)
-17 to 27 kg
(-37.48 to 59.52 lb)
-
FR Sensor Weight Info Front right sensor weight information/
Min.: -17 kg (-37.48 lb)
Max.: 27 kg (59.52 lb)
-17 to 27 kg
(-37.48 to 59.52 lb)
-
RL Sensor Weight Info Rear left sensor weight information/
Min.: -17 kg (-37.48 lb)
Max.: 37 kg (81.57 lb)
-17 to 37 kg
(-37.48 to 81.57 lb)
-
RR Sensor Weight Info Rear right sensor weight information/
Min.: -17 kg (-37.48 lb)
Max.: 37 kg (81.57 lb)
-17 to 37 kg
(-37.48 to 81.57 lb)
-
Total Weight Information Total weight information/
Min.: -68 kg (-149.91 lb)
Max.: 128 kg (282.19 lb)
-68 to 128 kg
(-149.91 to 282.19 lb)
-

Result:
Result Proceed to
Display is as specified in normal condition A
Display is not as specified in normal condition (for Power Seat) B
Display is not as specified in normal condition (for Manual Seat) C




A

5.REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH

B

REPLACE OCCUPANT CLASSIFICATION ECU

C

REPLACE OCCUPANT CLASSIFICATION ECU

5.REPLACE FRONT SEAT FRAME WITH ADJUSTER ASSEMBLY RH
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Replace the front seat frame with adjuster RH (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

HINT:

Perform the inspection using parts from a normal vehicle when possible.




NEXT

6.PERFORM ZERO POINT CALIBRATION
6.PERFORM ZERO POINT CALIBRATION
a.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Using the Techstream, perform the zero point calibration (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

7.PERFORM SENSITIVITY CHECK
7.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




NEXT

END

8.CHECK CONNECTORS
a.

Disconnect the connectors from the occupant classification ECU and front seat inner belt RH.


b.

Check that the connectors (on the occupant classification ECU side and front seat inner belt RH side) are not damaged.

OK:

Connectors are not deformed or damaged.




OK

9.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

NG

REPLACE NO. 2 FLOOR WIRE

9.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Replace the front seat inner belt RH (see page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).


d.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.



NEXT

10.PERFORM ZERO POINT CALIBRATION
10.PERFORM ZERO POINT CALIBRATION
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Using the Techstream, perform the zero point calibration (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).



NEXT

11.PERFORM SENSITIVITY CHECK
11.PERFORM SENSITIVITY CHECK
a.

Using the Techstream, perform the sensitivity check (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION).

Standard range:

27 to 33 kg (59.5 to 72.8 lb)




NEXT

END