Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM
RM27M0U _58 Vehicle Interior _049132 SEAT BELT _0234223 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

The combination meter assembly illuminates, blinks or turns off the seat belt warning light on the combination meter assembly in accordance with the state of the front seat inner belt assembly LH.

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


WIRING DIAGRAM

B289103E51
5.49,1.917 6.781,2.281 1.292,0.365 10 false Front Seat Inner Belt Assembly LH 5.49,1.75 6.052,2.063 0.563,0.313 10 false P7 3.156,1.906 5.146,2.125 1.99,0.219 10 false Center Airbag Sensor Assembly 5.052,4.323 6.865,4.552 1.813,0.229 10 false : CAN Communication Line 0.271,1.75 2.031,2.125 1.76,0.375 10 false Main Body ECU (Driver Side Junction Block Assembly) 0.479,4.208 1.667,4.573 1.188,0.365 10 false Combination Meter Assembly 3.167,1.75 3.417,1.927 0.25,0.177 10 false P1 5.365,1.094 5.51,1.323 0.146,0.229 10 false 2 5.365,0.292 5.49,0.531 0.125,0.24 10 false 1 3.979,0.417 4.375,0.667 0.396,0.25 10 false DBE+ 4,1.219 4.385,1.448 0.385,0.229 10 false DBE- 3.302,0.865 3.667,1.115 0.365,0.25 10 false CAN 1.26,0.854 1.594,1.083 0.333,0.229 10 false CAN 1.271,3.292 1.604,3.479 0.333,0.188 10 false CAN 4.448,0.302 4.688,0.51 0.24,0.208 10 false 11 4.448,1.094 4.75,1.365 0.302,0.271 10 false 12 5.583,0.292 6.052,0.51 0.469,0.219 10 false LBE+ 5.583,1.333 5.979,1.542 0.396,0.208 10 false LBE-

CAUTION / NOTICE / HINT

NOTICE:

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.CHECK DTC (AIRBAG SYSTEM)

b.

Recheck for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.READ VALUE USING TECHSTREAM (DRIVER BUCKLE SW)

B

2.READ VALUE USING TECHSTREAM (DRIVER BUCKLE SW)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / SRS Airbag / Data List.


e.

Read the Data List according to the display on the Techstream.

SRS Airbag (Center Airbag Sensor Assembly)
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Driver Buckle SW Driver buckle switch / Unset, Set or NG Unset: Seat belt not fastened
Set: Seat belt fastened
NG: Data is not determined
-

Result
Result Proceed to
Unset or Set is displayed on the Techstream screen according to the driver seat belt condition A
Unset or Set is not displayed normally on the Techstream screen according to the driver seat belt condition B
NG is displayed on the Techstream screen (for Column Shift Type) C
NG is displayed on the Techstream screen (for Floor Shift Type) D



A

3.REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

B

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

C

D

3.REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Replace the main body ECU (driver side junction block assembly) with a new one.



NEXT

4.CHECK SEAT BELT WARNING LIGHT
4.CHECK SEAT BELT WARNING LIGHT
a.

Check the operation of the seat belt warning light (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>OPERATION CHECK).

OK:

The seat belt warning light operates normally.




OK

END (MAIN BODY ECU [DRIVER SIDE JUNCTION BLOCK ASSEMBLY] WAS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY