Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049135 AUDIO / VIDEO _0234292 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Reverse Signal Circuit  


DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly.

WIRING DIAGRAM

E280105E07
5.625,0.76 6.083,0.958 0.458,0.198 10 false REV 5.427,0.656 5.885,0.854 0.458,0.198 10 false 2 5.51,1.375 5.969,1.573 0.458,0.198 10 false J139 5.531,1.563 6.75,1.917 1.219,0.354 10 false Radio and Display Receiver Assembly 4.208,0.646 4.667,0.844 0.458,0.198 10 false 1 3.927,0.635 4.385,0.833 0.458,0.198 10 false RL 3.104,1.146 4.031,1.333 0.927,0.188 10 false D35 3.125,1.313 4.521,1.688 1.396,0.375 10 false Park/Neutral Position Switch Assembly 0.458,0.771 1.677,0.969 1.219,0.198 10 false from ACC Fuse*1 3.115,0.667 3.573,0.865 0.458,0.198 10 false 2 3.313,0.635 3.771,0.833 0.458,0.198 10 false RB 0.156,2.146 1.719,2.406 1.563,0.26 10 false *1: for Column Shift Type 0.156,2.417 1.781,2.656 1.625,0.24 10 false *2: for Floor Shift Type 0.135,1 1.677,1.208 1.542,0.208 10 false from BK/UP LP Fuse*2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E286167E05
0.581,1.236 1.726,1.401 1.145,0.164

Enter the "Vehicle Signal Check Mode" screen. [Refer to check Vehicle Signal in Operation Check (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PROBLEM SYMPTOMS TABLE)].


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R ON
Except R OFF


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
U152700E01
0.067,0.058 0.309,0.243 0.242,0.186 10 *a 1.522,0.497 1.886,0.687 0.364,0.191 10 J139 0.063,0.733 0.392,0.904 0.330,0.171 10 REV 0.944,1.363 0.643,0.82 0.643,0.82 0.459,0.82 false

a.

Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J139-2 (REV) - Body ground Ignition switch ON, shift lever in R 7.5 to 14 V
J139-2 (REV) - Body ground Ignition switch ON, shift lever not in R Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)

Result
Result Proceed to
OK (for Column Shift Type) A
OK (for Floor Shift Type) B
NG C



A

B

C

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the J139 radio and display receiver assembly connector.


b.

Disconnect the D35 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J139-2 (REV) - D35-1 (RL) Always Below 1 Ω
J139-2 (REV) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
U152817E02
1.781,0.969 2,0.302 2,0.302 2.219,0.302 true 2.281,0.208 2.573,0.417 0.292,0.208 10 false RB 0.292,1.031 0.583,1.24 0.292,0.208 10 false D35 0.094,0.083 0.385,0.292 0.292,0.208 10 false *a

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D35-2 (RB) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/neutral Position Switch Assembly)

HINT:

If replacing the park/neutral position switch assembly, refer to the procedures below.





OK

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR