Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049135 AUDIO / VIDEO _0234292 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

Audio function:

This circuit is necessary for the automatic sound levelizer (ASL) built into the radio and display receiver assembly.

ASL function:

Speed signals are received from the combination meter assembly and used for the ASL.

The ASL function automatically adjusts the sound volume in order to maintain clear audio sound even when vehicle noise increases (as vehicle noise increases, the volume is turned up, etc.).

HINT:
·

A voltage of 12 V or 5 V is output from each ECU connected to the combination meter assembly, and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective systems based on the pulse signal.

·

If a short occurs in any of the ECU or in the wire harness connected to an ECU, related components will not operate normally.



WIRING DIAGRAM

E280104E03
5.469,1.604 5.917,1.781 0.448,0.177 10 false J139 5.469,1.781 6.781,2.219 1.313,0.438 10 false Radio and Display Receiver Assembly 0.156,1.542 0.604,1.719 0.448,0.177 10 false J28 0.156,1.74 1.469,2.146 1.313,0.406 10 false Combination Meter Assembly 2.979,1.479 4.146,1.74 1.167,0.26 10 false to Related ECUs 1.521,0.948 1.792,1.146 0.271,0.198 10 false 29 5.302,0.969 5.552,1.167 0.25,0.198 10 false 17 5.563,1.042 5.969,1.24 0.406,0.198 10 false SPD 1.208,1.073 1.479,1.271 0.271,0.198 10 false +S

PROCEDURE

1.CHECK VEHICLE SIGNAL
a.
E286167E03
1.724,0.732 2.889,0.896 1.165,0.164

Enter the "Vehicle Signal Check Mode" screen. [Refer to Check Vehicle Signal Check Mode in Operation Check (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK)]


b.

While driving the vehicle, compare the value of "SPEED" to the reading on the speedometer.

i.

Check if these readings are almost equal.

OK:

Vehicle speed displayed on the "Vehicle Signal Check Mode" screen is almost the same as the reading on the speedometer.





OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the J139 radio and display receiver assembly connector.


b.

Disconnect the J28 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J139-17 (SPD) - J28-29 (+S) Always Below 1 Ω
J139-17 (SPD) - Body ground Always 10 kΩ or higher




OK

3.INSPECT COMBINATION METER ASSEMBLY (SPEED SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT COMBINATION METER ASSEMBLY (SPEED SIGNAL)
a.
U152804E02
0.677,0.99 2.646,0.99 false 0.885,1.99 1.615,1.99 false 1.719,1.99 2.521,1.99 false 1.771,1.594 2.052,2.104 2.052,2.104 2.302,2.104 true 0.073,0.063 0.323,0.281 0.25,0.219 10 false *a 0.313,1.417 0.604,1.573 0.292,0.156 10 false J28 1.167,4.042 1.365,4.198 0.198,0.156 10 false A 2.344,2.01 2.573,2.167 0.229,0.156 10 false +S 2.813,3.458 3.198,3.615 0.385,0.156 10 false GND

Check the input waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal J28-29 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Terminal No. (Symbol) J28-29 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Being driven at approximately 20 km/h (12 mph)

OK:

The waveform displayed is as shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses.

As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)

Result
Result Proceed to
OK (for Column Shift Type) A
OK (for Floor Shift Type) B
NG C




A

B

C