Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049135 AUDIO / VIDEO _0234292 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B1532  LVDS Signal Malfunction (from Extension Module)  B156C  Extension Module Disconnected  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
B1532 When either condition below is met:.
·

The stereo component tuner assembly is not connected while the ignition switch is ON or ACC.

·

Communication between the radio and display receiver assembly and the stereo component tuner assembly is not possible when the engine is started.


·

No. 1 navigation wire

·

Stereo component tuner assembly

·

Radio and display receiver assembly


B156C

WIRING DIAGRAM

E280906E11
6.135,0.417 6.563,0.594 0.427,0.177 10 false US4- 5.771,0.427 6.198,0.604 0.427,0.177 10 false K5 5.771,0.865 6.198,1.042 0.427,0.177 10 false K5 5.771,1.302 6.198,1.479 0.427,0.177 10 false K5 5.771,1.75 6.198,1.927 0.427,0.177 10 false K5 5.771,2.188 6.198,2.365 0.427,0.177 10 false K5 5.802,0.198 5.927,0.375 0.125,0.177 10 false 2 6.135,0.854 6.563,1.031 0.427,0.177 10 false US4+ 5.802,0.656 5.927,0.833 0.125,0.177 10 false 3 6.135,1.74 6.563,1.917 0.427,0.177 10 false USV4 5.813,1.531 5.938,1.708 0.125,0.177 10 false 1 5.875,4.906 7.146,5.417 1.271,0.51 10 false Radio and Display Receiver Assembly 0.104,4.906 1.333,5.313 1.229,0.406 10 false Stereo Component Tuner Assembly 0.896,6.365 2.813,6.542 1.917,0.177 10 false : LVDS Communication Line 2.927,5.146 4.365,5.344 1.438,0.198 10 false No. 1 Navigation Wire 0.719,0.417 1.073,0.594 0.354,0.177 10 false US4- 0.677,0.875 1.063,1.052 0.385,0.177 10 false US4+ 0.677,1.729 1.063,1.906 0.385,0.177 10 false USV4 6.135,2.198 6.563,2.375 0.427,0.177 10 false USG4 5.833,1.99 5.958,2.167 0.125,0.177 10 false 5 0.635,2.188 1.063,2.365 0.427,0.177 10 false USG4 3.323,2.313 3.969,2.49 0.646,0.177 10 false Shielded 6.135,1.292 6.563,1.469 0.427,0.177 10 false UGD4 0.635,1.302 1.063,1.479 0.427,0.177 10 false UGD4 5.813,1.094 5.938,1.271 0.125,0.177 10 false 4 5.771,2.896 6.198,3.073 0.427,0.177 10 false L2 5.771,3.333 6.198,3.51 0.427,0.177 10 false L2 5.771,3.771 6.198,3.948 0.427,0.177 10 false L2 6.135,3.323 6.563,3.5 0.427,0.177 10 false ACC2 5.813,3.125 5.938,3.302 0.125,0.177 10 false 3 0.646,3.313 1.063,3.49 0.417,0.177 10 false ACC2 6.135,3.771 6.563,3.948 0.427,0.177 10 false GND2 5.813,3.563 5.938,3.74 0.125,0.177 10 false 8 0.635,3.781 1.063,3.958 0.427,0.177 10 false GND2 6.135,2.885 6.563,3.063 0.427,0.177 10 false +B2 0.771,2.885 1.063,3.063 0.292,0.177 10 false +B2 5.813,2.677 5.938,2.854 0.125,0.177 10 false 4 6.135,4.385 6.563,4.563 0.427,0.177 10 false LV 0.865,4.396 1.135,4.573 0.271,0.177 10 false LV 1.219,0.427 1.646,0.604 0.427,0.177 10 false K2 1.219,0.865 1.646,1.042 0.427,0.177 10 false K2 1.219,1.313 1.646,1.49 0.427,0.177 10 false K2 1.219,1.74 1.646,1.917 0.427,0.177 10 false K2 1.219,2.188 1.646,2.365 0.427,0.177 10 false K2 1.26,0.198 1.385,0.375 0.125,0.177 10 false 2 1.271,0.656 1.396,0.833 0.125,0.177 10 false 3 1.271,1.531 1.396,1.708 0.125,0.177 10 false 1 1.302,1.979 1.427,2.156 0.125,0.177 10 false 5 1.271,1.094 1.396,1.271 0.125,0.177 10 false 4 1.219,2.885 1.646,3.063 0.427,0.177 10 false L3 1.219,3.344 1.646,3.521 0.427,0.177 10 false L3 1.219,3.771 1.646,3.948 0.427,0.177 10 false L3 1.271,3.125 1.396,3.302 0.125,0.177 10 false 3 1.271,3.573 1.396,3.75 0.125,0.177 10 false 8 1.271,2.677 1.396,2.854 0.125,0.177 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

After replacing the stereo component tuner assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary.


PROCEDURE

1.CHECK FOR DTC

OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT TUNER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT TUNER ASSEMBLY)
a.

Disconnect the K5 and L2 radio and display receiver assembly connectors.


b.

Disconnect the K2 and L3 stereo component tuner assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K5-1 (USV4) - K2-1 (USV4) Always Below 1 Ω
K5-2 (US4-) - K2-2 (US4-) Always Below 1 Ω
K5-3 (US4+) - K2-3 (US4+) Always Below 1 Ω
K5-4 (UGD4) - K2-4 (UGD4) Always Below 1 Ω
K5-5 (USG4) - K2-5 (USG4) Always Below 1 Ω
L2-4 (+B2) - L3-4 (+B2) Always Below 1 Ω
L2-3 (ACC2) - L3-3 (ACC2) Always Below 1 Ω
L2-8 (GND2) - L3-8 (GND2) Always Below 1 Ω
K5-1 (USV4) - Body ground Always 10 kΩ or higher
K5-2 (US4-) - Body ground Always 10 kΩ or higher
K5-3 (US4+) - Body ground Always 10 kΩ or higher
K5-4 (UGD4) - Body ground Always 10 kΩ or higher
K5-5 (USG4) - Body ground Always 10 kΩ or higher
L2-4 (+B2) - Body ground Always 10 kΩ or higher
L2-3 (ACC2) - Body ground Always 10 kΩ or higher
L2-8 (GND2) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK A
NG (for Column Shift Type) B
NG (for Floor Shift Type) C



A

3.CHECK NO. 1 NAVIGATION WIRE (LVDS COMMUNICATION LINE)

B

C

3.CHECK NO. 1 NAVIGATION WIRE (LVDS COMMUNICATION LINE)

OK

END (NO. 1 NAVIGATION WIRE [LVDS COMMUNICATION LINE] IS DEFECTIVE)

NG

4.CHECK STEREO COMPONENT TUNER ASSEMBLY
4.CHECK STEREO COMPONENT TUNER ASSEMBLY
a.

Replace the stereo component tuner assembly with a known good one.




c.

Check for DTCs (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.


Result
Result Proceed to
OK A
NG (for Column Shift Type) B
NG (for Floor Shift Type) C



A

END (STEREO COMPONENT TUNER ASSEMBLY IS DEFECTIVE)

B

C