Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Power Seat)
RM27M0U _58 Vehicle Interior _049136 SEAT _0234295 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSTALL FRONT SEAT CUSHION SHIELD WIRE LH

a.

Install the front seat cushion shield wire LH with the 2 screws.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 2.INSTALL FRONT SEAT CUSHION SHIELD WIRE RH (for Front Passenger Side)

a.

Install the front seat cushion shield wire RH with the 2 screws.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 72125N 3.INSTALL UPPER NO. 4 SEAT TRACK COVER

a.

Attach the 2 claws to install the upper No. 4 seat track cover.


Hide 72125M 4.INSTALL UPPER NO. 3 SEAT TRACK COVER

HINT:

Use the same procedure described for the upper No. 4 seat track cover.


Hide 72125A 5.INSTALL UPPER SEAT TRACK COVER

a.

Attach the 2 claws to install the upper seat track cover.

HINT:

Use the same procedure for all upper seat track covers.



Hide 71874C 6.INSTALL FRONT LOWER SEAT CUSHION SHIELD LH (for Driver Side)

a.

Attach the claw to install the front lower seat cushion shield LH.


b.

Install the screw and attach the hook.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 71873A 7.INSTALL FRONT LOWER SEAT CUSHION SHIELD RH (for Driver Side)

HINT:

Use the same procedure described for the LH side.


Hide 71874C 8.INSTALL FRONT LOWER SEAT CUSHION SHIELD LH (for Front Passenger Side)

a.

Attach the 2 claws to install the front lower seat cushion shield LH.


Hide 71873A 9.INSTALL FRONT LOWER SEAT CUSHION SHIELD RH (for Front Passenger Side)

HINT:

Use the same procedure described for the LH side.


Hide 71620S 10.INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

a.

Attach the 4 hooks of the rear side to install the separate type front seat cushion spring assembly.


b.

Attach the hook of the front side.


Hide 71703C 11.INSTALL FRONT SEAT CUSHION PANEL SUB-ASSEMBLY

a.

Install the front seat cushion panel sub-assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82192 12.INSTALL FRONT SEAT CUSHION WIRE LH (for Driver Side)

a.

for 8 Way Seat Type:

i.
U152064E02
2.24,0.729 2.708,0.729 true 1.729,1.083 1.729,1.344 true 2.375,1.677 2.375,1.865 false 1.26,0.688 1.729,0.688 false 1.094,0.615 1.24,0.771 0.146,0.156 10 false *1 2.729,0.667 2.906,0.833 0.177,0.167 10 false *2 1.646,1.365 1.823,1.531 0.177,0.167 10 false *2 2.302,1.875 2.479,2.042 0.177,0.167 10 false *2

w/o Seat Heater System:

Connect the connector and attach the connector clamp and 3 wire harness clamps to install the front seat cushion wire LH.

Text in Illustration
*1 Connector Clamp
*2 Wire Harness Clamp


ii.
U152065E02
1.688,0.625 1.438,0.469 true 2.26,0.792 2.729,0.792 true 1.729,1.094 1.729,1.323 true 2.354,1.729 2.354,1.885 true 1.104,0.792 1.344,0.865 true 1.229,0.323 1.406,0.49 0.177,0.167 10 false *1 2.75,0.729 2.927,0.896 0.177,0.167 10 false *2 1.635,1.344 1.813,1.51 0.177,0.167 10 false *2 0.885,0.635 1.063,0.802 0.177,0.167 10 false *1 2.281,1.917 2.458,2.083 0.177,0.167 10 false *2

w/ Seat Heater System:

Connect the connector and attach the 2 connector clamps and 3 wire harness clamps to install the front seat cushion wire LH.

Text in Illustration
*1 Connector Clamp
*2 Wire Harness Clamp



b.
U152066E02
1.698,0.792 1.396,0.667 true 2.208,0.948 2.677,0.948 true 2.49,0.458 2.74,0.458 true 1.719,1.24 1.719,1.5 true 2.292,1.802 2.292,1.917 true 1.052,0.885 1.313,0.969 true 1.208,0.542 1.385,0.708 0.177,0.167 10 false *1 2.708,0.885 2.885,1.052 0.177,0.167 10 false *2 1.635,1.542 1.813,1.708 0.177,0.167 10 false *2 0.854,0.792 1.031,0.958 0.177,0.167 10 false *1 2.76,0.385 2.938,0.552 0.177,0.167 10 false *2 2.208,1.927 2.385,2.094 0.177,0.167 10 false *2

for 10 Way Seat Type:

i.

Connect the 2 connectors and attach the 2 connector clamps and 4 wire harness clamps to install the front seat cushion wire LH.

Text in Illustration
*1 Connector Clamp
*2 Wire Harness Clamp



c.
B354933

Connect the 2 connectors.


d.
B354932

Connect the connector and attach the 2 claws.


Hide 82191 13.INSTALL FRONT SEAT CUSHION WIRE RH (for Front Passenger Side)

a.
U152067E02
1.406,0.448 1.083,0.271 true 1.146,0.781 0.854,0.573 true 0.771,1.323 1.094,1.26 true 2.948,1.26 3.156,1.042 true 2.302,0.885 2.302,1.146 true 1.813,0.896 1.813,1.156 true 1.75,0.667 2.052,0.552 true 2.406,1.635 2.135,1.635 true 0.875,0.167 1.052,0.333 0.177,0.167 10 false *1 1.104,1.156 1.281,1.323 0.177,0.167 10 false *2 3.198,0.938 3.375,1.104 0.177,0.167 10 false *2 2.229,1.177 2.406,1.344 0.177,0.167 10 false *2 1.948,1.563 2.125,1.729 0.177,0.167 10 false *2 0.635,0.427 0.813,0.594 0.177,0.167 10 false *2 2.042,0.427 2.219,0.594 0.177,0.167 10 false *1 1.708,1.167 1.885,1.333 0.177,0.167 10 false *2

Connect the 4 connectors and attach the 2 connector clamps and 6 wire harness clamps to install the front seat cushion wire RH.

Text in Illustration
*1 Connector Clamp
*2 Wire Harness Clamp


Hide 85863 14.INSTALL SEAT CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)

a.

Install the seat climate control blower LH with the 3 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Attach the clamp.


Hide 85866A 15.INSTALL SEAT CUSHION CLIMATE CONTROL DUCT LH (w/ Climate Control Seat System)

a.

Attach the 2 claws to install the seat cushion climate control duct LH.


b.

Attach the 2 clips.


Hide 87501B 16.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)

a.

Attach the clamp to install the seat heater control sub-assembly LH.


b.

Connect the connector.


Hide 89952 17.INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side)

Hide 87510L 18.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)

Hide 71072S 19.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

a.

Set the separate type front seat cushion cover in place.


b.
B354927E01
0.585,0.45 0.745,0.606 0.159,0.156 10 *1 2.557,0.45 2.717,0.606 0.159,0.156 10 *1 1.154,0.338 0.768,0.514 false 0.224,2.461 0.384,2.617 0.159,0.156 10 *a 0.409,2.865 0.568,3.020 0.159,0.156 10 *2 0.867,2.216 0.424,2.486 false 2.156,0.338 2.542,0.514 false 1.021,2.95 0.617,2.95 false

Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 10 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.



HINT:

Install the hog rings at the cutouts if they are there.



c.

Attach the 2 fasteners.

Text in Illustration
*1 Fastener
*2 Hog Ring Pliers
*a Cutout


Hide 20.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

a.

Set the separate type front seat cushion cover with pad on the front seat cushion frame sub-assembly LH.


b.

for Driver Side:

i.
B354923E01
0.34,2.382 0.500,2.545 0.161,0.163 10 *a 0.557,2.82 0.718,2.983 0.161,0.163 10 *1 1.064,2.138 0.529,2.425 false 1.179,2.912 0.738,2.912 false

w/ Leg Support Adjustment Switch:

Using hog ring pliers, install the separate type front seat cushion cover to the front seat cushion frame sub-assembly LH with 4 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.



HINT:

Install the hog rings at the cutouts if they are there.


Text in Illustration
*1 Hog Ring Pliers
*a Cutout


ii.

w/ Leg Support Adjustment Switch:

Attach the 4 hooks.


iii.

Attach the 11 hooks to install the separate type front seat cushion cover with pad.

B354920



c.

for Front Passenger Side:

i.

Attach the 12 hooks to install the separate type front seat cushion cover with pad.

B354924



d.
U152063E02
1.125,1.365 0.802,1.365 false 2.052,0.885 2.438,0.885 false 2.063,1.49 2.427,1.49 false 0.635,1.313 0.802,1.479 0.167,0.167 10 false *1 2.49,0.813 2.656,0.979 0.167,0.167 10 false *2 2.5,1.438 2.667,1.604 0.167,0.167 10 false *2

Attach the connector clamp and 2 wire harness clamps to connect the seat cushion wire LH.

Text in Illustration
*1 Connector Clamp
*2 Wire Harness Clamp


e.

Connect the connector.


Hide 85867A 21.INSTALL SEATBACK CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)

a.
B354918

Install the seatback climate control blower LH in the direction indicated by the arrow shown in the illustration.


b.
B356555

Attach the 2 hooks.


c.
B359182

Spread the wires of the lumbar support assembly LH in the direction indicated by the arrow shown in the illustration to attach the 2 claws.


Hide 23.INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH

Hide 82192A 24.INSTALL FRONT SEATBACK WIRE LH (for Driver Side)

a.
B354945

w/o Climate Control Seat System:

i.

Attach the 3 clamps to install the front seatback wire LH.


ii.

Connect the 2 connectors.



b.
B354914

w/ Climate Control Seat System:

i.

Attach the 5 clamps to install the front seatback wire LH.


ii.

Connect the 3 connectors.



Hide 82191A 25.INSTALL FRONT SEATBACK WIRE RH (for Front Passenger Side)

a.
B356554

Attach the 4 clamps to install the front seatback wire RH.


b.

Connect the 3 connectors.


Hide 71552S 27.INSTALL SEPARATE TYPE FRONT SEATBACK PAD

a.

Install the separate type front seatback pad to the front seatback frame sub-assembly LH.


b.

w/ Climate Control Seat System:

i.

Attach the 6 clips.



Hide 87510N 28.INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)

Hide 71074S 29.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

a.

Set the separate type front seatback cover in place.


b.

Attach the 4 claws to install the 2 front seat headrest supports.


c.
B354909E01
0.519,2.813 0.685,2.979 0.166,0.166 10 *1 0.205,2.422 0.371,2.588 0.166,0.166 10 *a 1.09,2.899 0.699,2.899 false 0.983,2.134 0.394,2.465 false

Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



HINT:

Install the hog rings at the cutouts if they are there.


Text in Illustration
*1 Hog Ring Pliers
*a Cutout


d.
B354911E01
1.248,0.514 0.649,0.514 false 0.483,0.426 0.646,0.585 0.163,0.158 10 *1 1.282,1.118 0.649,1.118 false 0.483,1.031 0.646,1.189 0.163,0.158 10 *1 1.365,0.236 0.649,0.236 false 2.118,0.514 2.717,0.514 false 2.101,1.118 2.734,1.118 false 2.001,0.236 2.717,0.236 false 0.483,0.149 0.646,0.307 0.163,0.158 10 *1 2.734,0.426 2.897,0.585 0.163,0.158 10 *1 2.734,1.031 2.897,1.189 0.163,0.158 10 *1 2.734,0.149 2.897,0.307 0.163,0.158 10 *1

Attach the 6 fasteners.

Text in Illustration
*1 Fastener


e.

Pass the 4 straps of the separate type front seatback cover through the separate type front seatback pad.


f.

Attach the 2 hooks.

CAUTION:
·

For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.

·

Make sure that the strap is not twisted after attaching the 2 hooks.

·

Attach the 2 hooks securely.



i.

Slide each hook to attach them.


ii.

Install the 4 clips.



g.
B356804

Close the 2 fasteners.


h.
B354905E01
2.502,1.613 2.782,1.613 false 2.798,1.517 2.997,1.689 0.199,0.172 10 *A

w/o Seat Heater System:

i.

Pass the 2 wire harnesses through the separate type front seatback cover.



i.

w/ Seat Heater System:

i.

Pass the 3 wire harnesses through the separate type front seatback cover.

Text in Illustration
*A w/ Seat Heater System



j.

Detach the hook.


Hide 30.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

a.

When reusing a bolt:

i.

Clean the threads of the bolt with non-residue solvent.


ii.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




b.
B354903

Install the separate type front seatback assembly with the 4 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


c.
B354902E01
2.159,0.376 2.966,0.387 false 2.285,1.023 2.972,1.035 false 2.204,0.536 2.806,1.031 2.806,1.031 2.113,1.602 false 3,0.294 3.175,0.453 0.175,0.159 10 *1 3,0.941 3.175,1.100 0.175,0.159 10 *2

Attach the connector clamp and 3 wire harness clamps to connect the wire harness of the front seat airbag assembly LH.

Text in Illustration
*1 Connector Clamp
*2 Wire Harness Clamp


d.
B354901

Attach the wire harness clamp to connect the wire harness of the front seatback wire LH.


e.

Connect the connector.


f.
B354900

w/ Seat Heater System:

i.

Attach the wire harness clamp to connect the wire harness of the front seatback heater assembly LH.


ii.

Connect the connector.



Hide 71868A 31.INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD LH

a.
B354899

Attach the guide in the direction indicated by the arrow shown in the illustration to install the front inner No. 1 seat cushion shield LH.


b.

Install the 2 screws.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 82192B 32.INSTALL FRONT NO. 2 SEAT WIRE LH (w/ Leg Support Adjustment Switch)

a.

Attach the 2 clamps to install the front No. 2 seat wire LH.


Hide 84928 33.INSTALL SEAT VARIABLE CUSHION SWITCH (w/ Leg Support Adjustment Switch)

Hide 84920D 34.INSTALL FRONT POWER SEAT LUMBAR SWITCH LH

Hide 84922C 35.INSTALL FRONT POWER SEAT SWITCH LH (w/o Seat Position Memory System)

Hide 84070 36.INSTALL POSITION CONTROL ECU AND SWITCH ASSEMBLY (w/ Seat Position Memory System)

a.

Install the position control ECU and switch with the 3 screws.


Hide 84921A 37.INSTALL RECLINING POWER SEAT SWITCH KNOB

a.

Attach the 2 claws to install the reclining power seat switch knob.


Hide 84921B 38.INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

a.

Attach the 2 claws to install the slide and vertical power seat switch knob.


Hide 71812D 39.INSTALL FRONT SEAT CUSHION SHIELD LH

a.
B354890E01
0.168,0.067 0.374,0.251 0.207,0.184 10 *A 0.168,1.574 0.374,1.758 0.207,0.184 10 *B

w/o Leg Support Adjustment Switch:

i.

Connect the 2 connectors and attach the clamp to install the front seat cushion shield LH.



b.

w/ Leg Support Adjustment Switch:

i.

Connect the 4 connectors and attach the clamp to install the front seat cushion shield LH.

Text in Illustration
*A w/o Leg Support Adjustment Switch
*B w/ Leg Support Adjustment Switch



c.
U152062E01
2.138,0.622 2.330,0.797 0.192,0.175 10 (2) 0.064,1.825 0.256,2.000 0.192,0.175 10 (1)

Attach the 2 claws, clip and guide as indicated by the arrows in the order shown in the illustration.


d.

Install the 2 screws.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


e.

Connect the 2 rubber bands.


Hide 73240 41.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

Hide 73230 42.INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)