Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM27M0U _58 Vehicle Interior _049136 SEAT _0234304 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2651  Reclining Sensor Malfunction  


DESCRIPTION

When the position control ECU and switch assembly does not receive a sensor signal despite forward or rearward movement of the seatback by power seat motor operation, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
B2651 The forward and rearward lock detection position of the sensor is the same.
·

Position control ECU and switch assembly

·

Front seatback frame sub-assembly LH (reclining motor)

·

Harness or connector



WIRING DIAGRAM

B352948E01
0.913,2.333 1.307,2.474 0.394,0.141 10 Z6 0.913,2.476 2.764,2.835 1.851,0.360 10 Front Power Seat Position Motor LH (Reclining Motor) 0.527,3.254 3.364,3.441 2.837,0.187 10 Front Seatback Frame Sub-assembly LH 2.227,1.969 2.621,2.110 0.394,0.141 10 3 2.227,0.957 2.621,1.098 0.394,0.141 10 1 2.227,0.453 2.621,0.594 0.394,0.141 10 2 2.227,1.465 2.621,1.607 0.394,0.141 10 4 5.161,2.06 5.584,2.201 0.423,0.141 10 SGND 4.826,2.537 6.470,2.952 1.644,0.415 10 Position Control ECU and Switch Assembly 5.161,1.047 5.556,1.188 0.394,0.141 10 RCL- 5.161,0.544 5.556,0.685 0.394,0.141 10 RCL+ 5.161,1.556 5.580,1.697 0.419,0.141 10 SSRR 4.774,2.06 5.060,2.201 0.286,0.141 10 Z10 4.814,1.047 5.070,1.188 0.256,0.141 10 Z9 4.814,0.544 5.070,0.685 0.256,0.141 10 Z9 4.774,1.556 5.046,1.697 0.272,0.141 10 Z10 4.852,1.852 4.958,1.993 0.106,0.141 10 1 4.82,0.84 5.004,0.981 0.184,0.141 10 11 4.852,0.336 4.958,0.477 0.106,0.141 10 9 4.828,1.348 5.012,1.490 0.184,0.141 10 11

PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (SEAT RECLINING)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the Techstream.

Driver Seat
Tester Display Test Part Control Ranger Diagnostic Note
Seat Reclining Seat reclining operation Front / OFF / Rear -

OK:

Motor operates normally.




OK

2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)

NG

5.INSPECT FRONT SEATBACK FRAME SUB-ASSEMBLY LH (RECLINING MOTOR)
2.CHECK POSITION CONTROL ECU AND SWITCH ASSEMBLY (RECLINING MOTOR CIRCUIT)
a.
U152030E02
0.094,0.073 0.302,0.281 0.208,0.208 10 false *a 0.406,0.938 0.604,1.104 0.198,0.167 10 false Z6

Disconnect the front seatback frame sub-assembly LH (reclining motor) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Z6-4 - Z6-3 Reclining switch on 4.8 to 5.1 V


Text in Illustration
*a Front view of wire harness connector
(to Front Seatback Frame Sub-assembly LH [Reclining Motor])



OK

3.CHECK FRONT SEATBACK FRAME SUB-ASSEMBLY LH (RECLINING MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEATBACK FRAME SUB-ASSEMBLY LH)
3.CHECK FRONT SEATBACK FRAME SUB-ASSEMBLY LH (RECLINING MOTOR)
a.
U152033E02
0.104,0.083 0.302,0.313 0.198,0.229 10 false *a 0.281,1 0.51,1.188 0.229,0.188 10 false Z6

Reconnect the front seatback frame sub-assembly LH (reclining motor) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Z6-4 - Body ground Reclining switch on 4.5 to 4.8 V


Text in Illustration
*a Component with harness connected
(Front Seatback Frame Sub-assembly LH [Reclining Motor])



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPLACE FRONT SEATBACK FRAME SUB-ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEATBACK FRAME SUB-ASSEMBLY LH)
a.

Disconnect the Z10 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z10-11 (SSRR) - Z6-4 Always Below 1 Ω
Z10-1 (SGND) - Z6-3 Always Below 1 Ω
Z10-11 (SSRR) or Z6-4 - Body ground Always 10 kΩ or higher
Z10-1 (SGND) or Z6-3 - Body ground Always 10 kΩ or higher




OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FRONT SEATBACK FRAME SUB-ASSEMBLY LH (RECLINING MOTOR)
a.

Remove the front seatback frame sub-assembly LH (reclining motor) (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY).


b.

Inspect the front seatback frame sub-assembly LH (reclining motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT MOTOR ASSEMBLY>INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEATBACK FRAME SUB-ASSEMBLY LH)

NG

REPLACE FRONT SEATBACK FRAME SUB-ASSEMBLY LH

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - FRONT SEATBACK FRAME SUB-ASSEMBLY LH)
a.

Disconnect the Z9 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z9-9 (RCL+) - Z6-2 Always Below 1 Ω
Z9-11 (RCL-) - Z6-1 Always Below 1 Ω
Z9-9 (RCL+) or Z6-2 - Body ground Always 10 kΩ or higher
Z9-11 (RCL-) or Z6-1 - Body ground Always 10 kΩ or higher




OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR