Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM
RM27M0U _58 Vehicle Interior _049137 DOOR LOCK _0234325 KEY REMINDER WARNING SYSTEM J

DOOR LOCK  KEY REMINDER WARNING SYSTEM  Key Reminder Buzzer does not Sound  


DESCRIPTION

The key reminder warning buzzer sounds when the driver side door is opened while the ignition switch is in the LOCK or ACC position. The key reminder warning buzzer is activated when the main body ECU sends a key switch signal and driver side courtesy switch signal to the combination meter.

HINT:

Since the key reminder warning system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting the CAN communication function in accordance with the "HOW TO PROCEED WITH TROUBLESHOOTING" procedures. Then, conduct the following inspection procedure.


WIRING DIAGRAM

B205678E03
3.969,2 5.677,2.188 1.708,0.188 10 false CAN Communication Line 6.208,2.104 6.688,2.271 0.479,0.167 10 false Buzzer 2.896,2.375 3.094,2.542 0.198,0.167 10 false J4 2.896,1.271 3.094,1.438 0.198,0.167 10 false J1 0.813,1.167 0.927,1.344 0.115,0.177 10 false 2 2.375,1.167 2.49,1.344 0.115,0.177 10 false 1 2.375,2.24 2.49,2.417 0.115,0.177 10 false 1 1.073,2.74 1.354,2.917 0.281,0.177 10 false P5 1.073,2.896 2.563,3.26 1.49,0.365 10 false Front Door Courtesy Light Switch LH 0.938,1.625 1.219,1.802 0.281,0.177 10 false J18 0.927,1.781 2.417,2.01 1.49,0.229 10 false Unlock Warning Switch 2.99,2.76 4.115,2.99 1.125,0.229 10 false Main Body ECU 5.615,2.76 6.927,2.948 1.313,0.188 10 false Combination Meter 3.177,2.375 3.594,2.563 0.417,0.188 10 false DCTY 3.167,1.271 3.583,1.458 0.417,0.188 10 false KSW 2.885,2.208 3.073,2.365 0.188,0.156 10 false 24 2.927,1.094 3.042,1.25 0.115,0.156 10 false 5

PROCEDURE

1.READ VALUE USING TECHSTREAM (FRONT DOOR COURTESY SWITCH LH)
a.

Check the Data List for proper functioning of the front door courtesy light switch LH.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door Courtesy SW Front door courtesy light switch LH signal / ON or OFF ON: Driver side door is open
OFF: Driver side door is closed
-

OK:

The display is as specified in the normal condition column.




OK

2.READ VALUE USING TECHSTREAM (UNLOCK WARNING SWITCH)

NG

2.READ VALUE USING TECHSTREAM (UNLOCK WARNING SWITCH)
a.

Check the Data List for proper functioning of the unlock warning switch.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Key Unlock Warning SW Unlock warning switch signal /ON or OFF ON: Key is in ignition key cylinder
OFF: No key is in ignition key cylinder
-

OK:

ON (Key is in ignition key cylinder) appears on the screen.




OK

REPLACE MAIN BODY ECU

NG

3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
E146811E08
0.344,0.333 1.177,0.531 0.833,0.198 10 false Not pushed 0.5,0.844 1.052,1.021 0.552,0.177 10 false Pushed 0.156,2.406 2.646,2.865 2.49,0.458 10 false Component without harness connected: (Unlock Warning Switch)

a.

Remove the unlock warning switch (see page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Not pushed 10 kΩ or higher
Pushed Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - MAIN BODY ECU AND BODY GROUND)
B443032E01
0.75,1.542 1.104,1.76 0.354,0.219 0.667,3.833 1.021,4.052 0.354,0.219 1.74,4.052 2.156,3.635 true 0.177,0.208 2.49,0.583 2.313,0.375 10 false Front view of wire harness connector: (to Unlock Warning Switch) 0.177,2.385 2.49,2.76 2.313,0.375 10 false Front view of wire harness connector: (to Main Body ECU) 0.781,3.854 1.24,4.052 0.458,0.198 10 false J1 0.823,1.563 1.281,1.76 0.458,0.198 10 false J18 2.198,3.521 2.656,3.719 0.458,0.198 10 false KSW

a.

Disconnect the J18 switch connector.


b.

Disconnect the J1 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J18-1 - J1-5 (KSW) Always Below 1 Ω
J18-2 - Body ground Always 10 kΩ or higher
J1-5 (KSW) - Body ground Always 10 kΩ or higher




OK

5.CHECK COMBINATION METER ASSEMBLY (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK COMBINATION METER ASSEMBLY (OPERATION)
a.

Temporarily replace the combination meter assembly with a new or normally functioning one (see page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>INSTALLATION).


b.

Check the key reminder warning system function.

OK:

The key reminder warning system functions properly.




OK

END (COMBINATION METER IS DEFECTIVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR