Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27M0U _54 Brake _049153 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0234401 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C0226/21  SFR Solenoid Circuit  C0236/22  SFL Solenoid Circuit  C0246/23  SRR Solenoid Circuit  C0256/24  SRL Solenoid Circuit  C1225/25  SMC Solenoid Circuit  C1226/26  SMC Solenoid Circuit  C1227/27  SRC Solenoid Circuit  C1228/28  SRC Solenoid Circuit  


DESCRIPTION

This solenoid is turned on in accordance with signals from the skid control ECU and controls the pressure on the wheel cylinders to control the braking force.

C160048E01
3.447,6.273 4.556,6.498 1.110,0.225 10 Skid Control ECU 3.731,1.085 4.211,1.311 0.480,0.225 10 SMC1 3.731,1.522 4.211,1.748 0.480,0.225 10 SMC2 3.731,1.953 4.211,2.178 0.480,0.225 10 SRC1 3.731,2.39 4.211,2.615 0.480,0.225 10 SRC2 3.731,2.828 4.211,3.053 0.480,0.225 10 SFRH 3.731,3.265 4.211,3.490 0.480,0.225 10 SFRR 3.731,3.695 4.211,3.921 0.480,0.225 10 SFLH 3.731,4.132 4.211,4.358 0.480,0.225 10 SFLR 3.731,4.56 4.211,4.786 0.480,0.225 10 SRRH 3.731,4.997 4.211,5.222 0.480,0.225 10 SRRR 3.731,5.428 4.211,5.653 0.480,0.225 10 SRLH 3.731,5.864 4.211,6.090 0.480,0.225 10 SRLR

DTC Code DTC Detection Condition Trouble Area
C0226/21
C0236/22
C0246/23
C0256/24
Open or short in solenoid circuit continues for 0.05 seconds or more. Skid control ECU
C1225/25
C1226/26
C122727
C1228/28
When any of following conditions detected:
1.

During switching solenoid (SMC1, SMC2, SRC1 or SRC2) ON signal input, overcurrent continues for 0.05 seconds or more.

2.

During switching solenoid (SMC1, SMC2, SRC1 or SRC2) OFF signal input, open circuit continues for 0.05 seconds or more.

3.

During switching solenoid (SMC1, SMC2, SRC1 or SRC2) ON signal input, open circuit continues for 0.01 seconds or more.

4.

During switching solenoid (SMC1, SMC2, SRC1 or SRC2) OFF signal input, current continues to be applied for 0.1 seconds or more.

5.

Short to GND in switching solenoid (SMC1, SMC2, SRC1 or SRC2) continues for 0.1 seconds or more.

6.

Switching solenoids (SMC1, SMC2, SRC1 or SRC2) shorted for 0.1 seconds or more.


Skid control ECU

CAUTION / NOTICE / HINT

NOTICE:

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.RECONFIRM DTC

b.

Start the engine.


c.

Check if the same DTC(s) is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B

HINT:

The DTCs may be stored due to a malfunction in the connector terminal.




A

B