Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › FRONT SPEED SENSOR
RM27M0U _54 Brake _049153 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0234403 FRONT SPEED SENSOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  FRONT SPEED SENSOR  INSTALLATION  


PROCEDURE

Hide 88266B 1.INSTALL FRONT SKID CONTROL SENSOR CLAMP LH

a.

Install the skid control sensor clamp (labeled A) with the bolt (labeled B).

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Install the bracket so that the rotation stopper (labeled C) touches the knuckle.


C154443E02
0.487,1.258 0.622,1.414 0.135,0.156 10 A 0.396,2.855 0.531,3.011 0.135,0.156 10 B 5.965,1.16 6.100,1.316 0.135,0.156 10 C 3.282,2.407 3.417,2.562 0.135,0.156 10 D 3.457,2.638 3.592,2.794 0.135,0.156 10 E


Hide 89543 2.INSTALL FRONT SPEED SENSOR LH

a.

Install the speed sensor (labeled D) with the hexagon socket head cap bolt (labeled E).

Torque:
11 N*m (107 kgf*cm, 8 ft.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the sensor tip part.

·

While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip part.

·

After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.

·

Make sure there is no foreign matter attached to the magnetic rotor.




Hide 89516 3.INSTALL FRONT SKID CONTROL SENSOR WIRE LH

a.
C154447E04
2.323,0.417 2.448,0.573 0.125,0.156 10 false A 0.396,0.448 0.521,0.604 0.125,0.156 10 false C 0.979,1.927 1.104,2.083 0.125,0.156 10 false B 3.146,2.156 3.271,2.313 0.125,0.156 10 false C 2.083,2.042 2.208,2.198 0.125,0.156 10 false B 3.26,1.344 3.385,1.5 0.125,0.156 10 false B 0.75,2.417 0.875,2.573 0.125,0.156 10 true C

Connect the connector (labeled A).


b.

Install the 3 harness clamps (labeled B) with the 3 bolts (labeled C).

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:
·

When installing the clamps, do not twist the wire harness.

·

For clamps with rotation stoppers, make sure the rotation stopper touches the installation position.




c.
C154445E02
0.089,2.457 0.217,2.617 0.128,0.161 10 D 0.744,3.078 0.872,3.238 0.128,0.161 10 E 1.34,3.214 1.468,3.375 0.128,0.161 10 E 1.484,3.47 1.612,3.630 0.128,0.161 10 E 2.243,4.044 2.371,4.204 0.128,0.161 10 F

Install the harness clamp with the bolt (labeled D).

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:
·

When installing the clamp, do not twist the wire harness.

·

Make sure the clamp's rotation stopper touches the installation position.




d.

Attach the 3 clips (labeled E).

NOTICE:
·

When installing the clips, do not twist the wire harness.

·

When installing the clips, securely insert them as shown in the illustration.




e.

Connect the speed sensor connector (labeled F).

NOTICE:

Securely connect the connector.



Hide 88266C 4.INSTALL FRONT SKID CONTROL SENSOR CLAMP RH

a.

Install the skid control sensor clamp (labeled A) with the bolt (labeled B).

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Install the bracket so that the rotation stopper (labeled C) touches the knuckle.


C154442E02
3.147,1.293 3.266,1.468 0.119,0.174 10 A 3.203,2.829 3.322,3.004 0.119,0.174 10 B 5.176,0.794 5.295,0.968 0.119,0.174 10 C 0.144,2.619 0.263,2.793 0.119,0.174 10 E 0.29,2.404 0.409,2.579 0.119,0.174 10 D


Hide 89542 5.INSTALL FRONT SPEED SENSOR RH

a.

Install the speed sensor (labeled D) with the hexagon socket head cap bolt (labeled E).

Torque:
11 N*m (107 kgf*cm, 8 ft.*lbf)

NOTICE:
·

Make sure there are no pieces of iron or other foreign matter attached to the sensor tip part.

·

While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip part.

·

After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.

·

Make sure there is no foreign matter attached to the magnetic rotor.




Hide 89516 6.INSTALL FRONT SKID CONTROL SENSOR WIRE RH

a.
C154446E06
2.031,0 2.156,0.156 0.125,0.156 10 false C 2.927,2.438 3.052,2.594 0.125,0.156 10 false E 2.677,0 2.802,0.156 0.125,0.156 10 false E 3.271,1.542 3.406,1.698 0.135,0.156 10 false D 2.104,1.958 2.229,2.115 0.125,0.156 10 true D 0.396,0.458 0.521,0.615 0.125,0.156 10 false A 0.063,0.854 0.229,1.042 0.167,0.188 10 true B

Install the skid control sensor clamp (labeled A) with the bolt (labeled B).

Torque:
for Bolt B : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Install the connector (labeled C) with connect the connector (labeled C).


c.

Install the 2 harness clamps (labeled D) with the 2 bolts (labeled E).

Torque:
for Bolt E : 13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:
·

When installing the clamps, do not twist the wire harness.

·

For clamps with rotation stoppers, make sure the rotation stopper touches the installation position.




d.
C154444E02
1.181,3.996 1.318,4.156 0.137,0.161 10 G 2.089,3.242 2.212,3.402 0.123,0.161 10 F 2.617,3.098 2.741,3.258 0.123,0.161 10 F 2.004,3.481 2.128,3.642 0.123,0.161 10 F 3.294,2.472 3.417,2.633 0.123,0.161 10 E

Install the harness clamp with the bolt (labeled E).

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:
·

When installing the clamp, do not twist the wire harness.

·

Make sure the clamp's rotation stopper touches the installation position.




e.

Attach the 3 clips (labeled F).

NOTICE:
·

When installing the clips, do not twist the wire harness.

·

When installing the clips, securely insert them as shown in the illustration.




f.

Connect the speed sensor connector (labeled G).

NOTICE:

Securely connect the connector.



Hide 7.INSTALL FRONT WHEEL

Torque:
for Aluminum Wheel : 131 N*m (1336 kgf*cm, 97 ft.*lbf)
for Steel Wheel : 209 N*m (2131 kgf*cm, 154 ft.*lbf)

Hide 28800 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 89543 9.CHECK SPEED SENSOR SIGNAL