Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › REAR SPEED SENSOR
RM27M0U _54 Brake _049153 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0234404 REAR SPEED SENSOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  REAR SPEED SENSOR  INSTALLATION  


PROCEDURE

Hide 89516B 1.INSTALL SKID CONTROL SENSOR WIRE

a.

Install the sensor clamp with the nut (labeled A).

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Make sure the clamp's rotation stopper touches the installation position.



b.

Install the sensor clamp with the bolt (labeled B).

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

When installing the clamp, do not twist the wire harness.



c.

Attach the 7 clips (labeled C).

NOTICE:
·

When installing the clamps, do not twist the wire harness.

·

When installing the clamps, securely insert them as shown in the illustration.




d.

Connect the sensor connector (labeled D).

NOTICE:

Securely connect the connector.


C154448E02
2.762,0.007 2.898,0.167 0.136,0.161 10 D 2.092,1.62 2.253,1.780 0.160,0.161 10 C 3.062,0.255 3.181,0.401 0.119,0.147 10 A 3.302,1.175 3.421,1.322 0.119,0.147 10 B 2.566,1.602 2.726,1.762 0.160,0.161 10 C 3.308,0.343 3.468,0.503 0.160,0.161 10 C 3.992,0.44 4.152,0.600 0.160,0.161 10 C 4.637,0.903 4.798,1.064 0.160,0.161 10 C 5.155,0.918 5.316,1.079 0.160,0.161 10 C 5.263,0.54 5.402,0.701 0.139,0.161 10 C


Hide 89546 2.INSTALL REAR SPEED SENSOR LH

a.
C154449E03
2.394,0.957 2.522,1.122 0.128,0.165 10 A 2.48,1.335 2.608,1.500 0.128,0.165 10 B 1.506,1.535 1.634,1.700 0.128,0.165 10 C

Install the speed sensor (labeled A) with the nut (labeled B).

Torque:
11 N*m (107 kgf*cm, 8 ft.*lbf)


b.

Connect the speed sensor connector (labeled C).

NOTICE:

Securely connect the connector.



Hide 89545 3.INSTALL REAR SPEED SENSOR RH

a.
C154450E02
1.148,1.203 1.266,1.352 0.118,0.149 10 A 1.112,1.614 1.230,1.763 0.118,0.149 10 B 2.376,1.618 2.494,1.767 0.118,0.149 10 C

Install the speed sensor (labeled A) with the nut (labeled B).

Torque:
11 N*m (107 kgf*cm, 8 ft.*lbf)


b.

Connect the speed sensor connector (labeled C).

NOTICE:

Securely connect the connector.



Hide 4.INSTALL REAR WHEEL

Torque:
for Aluminum Wheel : 131 N*m (1336 kgf*cm, 97 ft.*lbf)
for Steel Wheel : 209 N*m (2131 kgf*cm, 154 ft.*lbf)

Hide 28800 5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 89546 6.CHECK SPEED SENSOR SIGNAL