Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › TRAILER BRAKE CONTROL SYSTEM
RM27M0U _54 Brake _049153 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0234409 TRAILER BRAKE CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  TRAILER BRAKE CONTROL SYSTEM  C14A4  Output Circuit Temperature High / Over Current  C14A6  Output Circuit Negative Voltage  


DESCRIPTION

The trailer brake control ECU (brake control with bracket relay) is connected via the trailer socket and direct line.

The trailer brake control ECU (brake control with bracket relay) outputs a signal to the trailer socket.

DTC Code DTC Detection Condition Trouble Area
C14A4 When either of following conditions detected:
1.

Trailer brake control ECU (Brake control with bracket relay) output circuit temperature continuously exceeds 125°C for 2 seconds or more

2.

Trailer brake control ECU (Brake control with bracket relay) output circuit current value continuously exceeds 25 A for 2 seconds or more


·

Harness or connector (Vehicle)

·

Harness or connector (Trailer)

·

Trailer brake control ECU (Brake control with bracket relay)


C14A6 Voltage is continuously input to trailer brake control ECU (brake control with bracket relay) output circuit for 2 seconds or more
·

Harness or connector (Vehicle)

·

Harness or connector (Trailer)

·

Trailer brake control ECU (Brake control with bracket relay)



WIRING DIAGRAM

C311212E02
4.844,1.063 6.948,1.417 2.104,0.354 10 false Trailer Brake Control ECU (Brake Control with Bracket Relay) 4.458,1.063 4.865,1.26 0.406,0.198 10 false J156 0.948,1.729 1.354,1.885 0.406,0.156 10 false R18 5.188,0.542 5.646,0.698 0.458,0.156 10 false BRK 1.667,0.552 2.083,0.708 0.417,0.156 10 false BRK 1.656,1.271 2.083,1.427 0.427,0.156 10 false GND 4.969,0.427 5.26,0.583 0.292,0.156 10 false 7 2.073,0.438 2.313,0.594 0.24,0.156 10 false 6 2.063,1.167 2.354,1.323 0.292,0.156 10 false 3 1.24,1.729 2.302,2.01 1.063,0.281 10 false Trailer Socket

CAUTION / NOTICE / HINT

NOTICE:

The usable trailer output is limited to 24 A.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BRAKE CONTROL WITH BRACKET RELAY - TRAILER SOCKET)
a.

Turn the ignition switch off.


b.

Disconnect the J156 trailer brake control ECU (brake control with bracket relay) connector.


c.

Inspect both the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J156-7 (BRK) - R18-6 (BRK) Always Below 1 Ω
J156-7 (BRK) or R18-6 (BRK) - Body ground Always 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (VEHICLE)

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
U152663E01
0.083,1.849 0.501,1.988 0.418,0.139 10 GND 0.073,0.074 0.463,0.213 0.389,0.139 10 *a 0.528,1.926 0.715,1.926 0.715,1.926 1.389,1.166 false 0.219,0.979 0.637,1.118 0.418,0.139 10 R18

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R18-3 (GND) - Body ground Always Below 1 Ω

Text in Illustration
*a Front view of wire harness connector
(to Trailer Socket)




OK

3.CHECK HARNESS AND CONNECTOR (TRAILER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (VEHICLE)

3.CHECK HARNESS AND CONNECTOR (TRAILER)
a.

Check the wire harness and connector of the connected trailer.

Check items:
·

Connector link state

·

Connector looseness or disconnection

·

Deformation and corrosion of connector case and terminal

·

Standard voltage and resistance of wire harness and connector (refer to manual of each trailer for standard values)


OK:

No problem with check items.




OK

REPLACE BRAKE CONTROL WITH BRACKET RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRAILER)