Home › Vehicle Interior › AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM27M0U _58 Vehicle Interior _049154 AIR CONDITIONING _0234412 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1446/46  Air Mix Damper Control Servo Motor Circuit (Driver Side)  


DESCRIPTION

The No. 1 damper servo sub-assembly (air mix damper servo motor [for driver side]) sends pulse signals to inform the air conditioning amplifier of the damper position. The air conditioning amplifier activates the motor (normal, reverse) based on the signals to move the air mix damper (for driver side) to any position. As a result the amount of air that has passed through the evaporator and is now passing through the heater core is adjusted, and the temperature of the air blowing toward the driver side is controlled.

HINT:

Confirm that no mechanical problem is present because this diagnostic trouble code can be output when either a damper link or damper is mechanically locked.


DTC Code DTC Detection Condition Trouble Area
B1446/46 Air mix damper position sensor value does not change even if air conditioning amplifier operates No. 1 damper servo sub-assembly (air mix damper servo motor [for driver side])
·

No. 1 damper servo sub-assembly (air mix damper servo motor [for driver side])

·

Air conditioning harness

·

Air conditioning amplifier



WIRING DIAGRAM

E147168E09
5.253,0.969 5.777,1.119 0.523,0.150 10 B BUS 5.253,1.605 5.691,1.755 0.438,0.150 10 BUS 5.253,2.24 5.792,2.382 0.539,0.142 10 BUS G 5.008,0.884 5.185,1.030 0.177,0.146 10 4 5.008,1.504 5.185,1.650 0.177,0.146 10 3 5.008,2.124 5.185,2.269 0.177,0.146 10 2 0.589,2.826 2.616,3.367 2.027,0.542 10 No. 1 Damper Servo Sub-assembly (Air Mix Damper Servo Motor [For Driver Side]) 3.131,2.972 4.747,3.129 1.616,0.158 10 Air Conditioning Harness 5.177,2.962 6.805,3.104 1.629,0.142 10 z1 5.177,3.112 6.805,3.255 1.629,0.143 10 Air Conditioning Amplifier

PROCEDURE

1.READ VALUE USING TECHSTREAM (AIR MIX SERVO MOTOR TARGET PULSE (for Driver Side))
a.

Use the Data List to check if the servo motor is functioning properly.

Air Conditioner
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Air Mix Servo Targ Pulse (D) No. 1 damper servo sub-assembly (air mix damper servo motor [for driver side]) target pulse /
Min.: 0, Max.: 255
MAX. COLD: 5 (pulse)
MAX. HOT: 104 (pulse)
-

OK:

The display is as specified in the normal condition.


Result
Result Proceed to
OK (Checking from the DTC) A
OK (Checking from the PROBLEM SYMPTOMS TABLE) B
NG C



A

2.REPLACE NO. 1 DAMPER SERVO SUB-ASSEMBLY (AIR MIX SERVO MOTOR [for Driver Side])

B

C

REPLACE AIR CONDITIONING AMPLIFIER

2.REPLACE NO. 1 DAMPER SERVO SUB-ASSEMBLY (AIR MIX SERVO MOTOR [for Driver Side])
a.

Temporarily replace the No. 1 damper servo sub-assembly (air mix damper servo motor [for driver side]) with a new one (see page Vehicle Interior>AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY).

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new one and check that the condition returns to normal.




NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC

OK

END (AIR MIX SERVO MOTOR IS DEFECTIVE)

NG

4.REPLACE AIR CONDITIONING HARNESS
4.REPLACE AIR CONDITIONING HARNESS
a.

Replace the air conditioning harness.



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC

OK

END (AIR CONDITIONING HARNESS IS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER