Home › Vehicle Interior › AIR CONDITIONING › COMPRESSOR
RM27M0U _58 Vehicle Interior _049154 AIR CONDITIONING _0234425 COMPRESSOR A

AIR CONDITIONING  COMPRESSOR  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.

When replacing the compressor and magnetic clutch with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor and magnetic clutch before installation.

Standard:

(Oil capacity inside the new compressor and magnetic clutch: 120 + 15 cc (4.1 + 0.51 fl. oz.)) - (Remaining oil amount in the removed compressor and magnetic clutch) = (Oil amount to be removed from the new compressor when replacing)


NOTICE:
·

When checking the compressor oil level, follow the A/C system's precautions.

·

If a new compressor and magnetic clutch is installed without removing some oil remaining in the pipes of the vehicle, the oil amount will be too large. This prevents heat exchange in the refrigerant cycle and causes refrigerant failure.

·

If the volume of oil remaining in the removed compressor and magnetic clutch is too small, check for oil leakage.

·

Be sure to use ND-OIL 8 or equivalent for compressor oil.




Hide 88320 2.INSTALL COOLER COMPRESSOR ASSEMBLY

a.
E147759E01
3.22,1.576 3.351,1.753 0.132,0.177 10 2 3.224,0.609 3.355,0.786 0.132,0.177 10 3 2.504,1.506 2.635,1.683 0.132,0.177 10 4 2.768,0.74 2.900,0.916 0.132,0.177 10 1

Install the cooler compressor assembly and 2 stud bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install the 2 bolts and 2 nuts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

HINT:

Tighten the bolts and nuts in the order shown in the illustration to install the cooler compressor assembly.



c.

Connect the connector.


Hide 88712 3.CONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE

a.
E147758

Remove the attached vinyl tape from the No. 1 cooler refrigerant suction hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant suction hose.


d.

Connect the No. 1 cooler refrigerant suction hose to the cooler compressor assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.
E147757

Remove the attached vinyl tape from the No. 1 cooler refrigerant discharge hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.


d.

Connect the No. 1 cooler refrigerant discharge hose to the cooler compressor assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 53737B 6.INSTALL FRONT FENDER APRON SEAL LH

a.
E143269

Install the front fender apron seal LH with the 6 clips.