Home › Vehicle Interior › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM
RM27M0U _58 Vehicle Interior _049156 ENGINE IMMOBILISER _0234432 ENGINE IMMOBILISER SYSTEM C

ENGINE IMMOBILISER  ENGINE IMMOBILISER SYSTEM  B2797  Communication Malfunction No. 1  


DESCRIPTION

This DTC is output when a communication error occurs between the transponder key amplifier and transponder key ECU. Some possible reasons for the communication error are: 1) 2 or more ignition keys are positioned too close together, or 2) noise is occurring in the communication line.

DTC Code DTC Detection Condition Trouble Area
B2797 Keys are positioned too close to each other, or noise occurred in communication line
·

Key

·

Harness or connector

·

Transponder key amplifier

·

Transponder key ECU



WIRING DIAGRAM

B168145E16
5.469,1.135 5.948,1.323 0.479,0.188 10 false CODE 1.229,1.135 1.708,1.323 0.479,0.188 10 false CODE 1.76,1.063 2.438,1.344 0.677,0.281 10 false 4 5.188,1.063 5.865,1.344 0.677,0.281 10 false 15 5.198,2.146 7.01,2.5 1.813,0.354 10 false Transponder Key ECU 0.594,2.146 2.729,2.469 2.135,0.323 10 false Transponder Key Amplifier 0.604,1.99 1.063,2.188 0.458,0.198 10 false J20 5.198,1.99 5.656,2.188 0.458,0.198 10 false J26

CAUTION / NOTICE / HINT

HINT:

When the transponder key ECU is replaced, reregister the ECU - ECM communication ID (see page Vehicle Interior>ENGINE IMMOBILISER>ENGINE IMMOBILISER SYSTEM>REGISTRATION).


PROCEDURE

1.CHECK KEY
E146363

a.

Check whether the ignition key being used is near other ignition keys as shown in the illustration. Also, check whether the key ring is in contact with the key grip.

Result
Result Proceed to
Key is near other keys and/or key ring is in contact with key grip A
Key is not near other keys and/or key ring is not in contact with key grip B



A

2.CHECK FOR DTC

B

3.CHECK TRANSPONDER KEY ECU (NOISE)
2.CHECK FOR DTC
a.

Separate the keys from each other, or remove the key ring.



c.

Insert a key into the ignition key cylinder. Remove it. Repeat for all other keys.


d.

Check that no DTC is output (see page Vehicle Interior>ENGINE IMMOBILISER>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2797 is not output.




OK

END

NG

3.CHECK TRANSPONDER KEY ECU (NOISE)
3.CHECK TRANSPONDER KEY ECU (NOISE)
B443046E01
0.531,2.823 0.896,3.083 0.365,0.26 0.573,1.156 0.938,1.417 0.365,0.26 1.896,1.083 2.115,0.667 false 1.396,3.042 1.115,3.479 false 5.177,1.896 5.417,1.188 5.417,1.188 5.521,1.188 false 0.458,0.083 2.677,0.438 2.219,0.354 10 false Component with harness connected: (Transponder Key Amplifier) 0.458,1.896 2.667,2.292 2.208,0.396 10 false Component with harness connected: (Transponder Key ECU) 0.646,1.198 0.896,1.385 0.25,0.188 10 false J20 0.604,2.865 0.865,3.042 0.26,0.177 10 false J26 2.156,0.552 2.771,0.75 0.615,0.198 10 false CODE 0.708,3.427 1.323,3.625 0.615,0.198 10 false CODE 5.583,1.104 6.458,1.458 0.875,0.354 10 false Noise should not appear

a.

Using an oscilloscope, check for noise in the waveform between the terminals of the J20 amplifier connector and J26 ECU connector.

OK:
Tester Connection Tool Setting Condition Specified Condition
J26-15 (CODE) - J20-4 (CODE) 5 V/DIV., 20 msec./DIV. Key inserted in ignition key cylinder No noise is present




OK

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY AMPLIFIER)

NG

FIND CAUSE OF NOISE AND REMOVE IT

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY AMPLIFIER)
B443042E03
0.333,1.427 0.656,1.656 0.323,0.229 0.583,3.625 0.906,3.854 0.323,0.229 2.208,1.656 2.385,2.073 false 1.667,3.854 1.406,4.354 false 0.156,0.156 2.427,0.531 2.271,0.375 10 false Front view of wire harness connector: (to Transponder Key ECU) 0.167,2.531 2.438,2.885 2.271,0.354 10 false Front view of wire harness connector: (to Transponder Key Amplifier) 0.385,1.458 0.615,1.625 0.229,0.167 10 false J26 0.635,3.656 0.875,3.833 0.24,0.177 10 false J20 2.396,2.063 3.01,2.26 0.615,0.198 10 false CODE 1,4.281 1.615,4.479 0.615,0.198 10 false CODE

a.

Disconnect the J26 ECU connector.


b.

Disconnect the J20 amplifier connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J26-15 (CODE) - J20-4 (CODE) Always Below 1 Ω
J26-15 (CODE) or J20-4 (CODE) - Body ground Always 10 kΩ or higher




OK

5.REPLACE TRANSPONDER KEY AMPLIFIER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TRANSPONDER KEY AMPLIFIER
a.

Temporarily replace the transponder key amplifier with a new or normally functioning one (see page Vehicle Interior>ENGINE IMMOBILISER>TRANSPONDER KEY AMPLIFIER>REMOVAL).



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts normally.

OK:

Engine starts.




OK

END (TRANSPONDER KEY AMPLIFIER IS DEFECTIVE)

NG