Home › Vehicle Interior › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM
RM27M0U _58 Vehicle Interior _049156 ENGINE IMMOBILISER _0234432 ENGINE IMMOBILISER SYSTEM C

ENGINE IMMOBILISER  ENGINE IMMOBILISER SYSTEM  B2780  Push Switch / Key Unlock Warning Switch Malfunction  


DESCRIPTION

This DTC will be output if the transponder key ECU does not detect that the unlock warning switch is ON even when the ignition switch is ON. Under normal conditions, the unlock warning switch is ON when the ignition switch is ON.

DTC Code DTC Detection Condition Trouble Area
B2780 Unlock warning switch ON is not detected when the ignition switch is ON.
·

Transponder key ECU

·

Unlock warning switch

·

Harness or connector



WIRING DIAGRAM

E146342E13
2.708,1.635 4.198,1.875 1.49,0.24 10 false Unlock Warning Switch 2.854,1.042 3,1.219 0.146,0.177 10 false 2 3.885,1.042 4.031,1.219 0.146,0.177 10 false 1 5.469,1.042 5.615,1.219 0.146,0.177 10 false 3 5.708,1.167 6.156,1.354 0.448,0.188 10 false KSW 5.365,2.125 6.958,2.479 1.594,0.354 10 false Transponder Key ECU 2.719,1.469 3.177,1.667 0.458,0.198 10 false J18 5.365,1.979 5.823,2.177 0.458,0.198 10 false J26

CAUTION / NOTICE / HINT

HINT:

When the transponder key ECU is replaced, reregister the ECU - ECM communication ID (see page Vehicle Interior>ENGINE IMMOBILISER>ENGINE IMMOBILISER SYSTEM>REGISTRATION).


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTC (see page Vehicle Interior>ENGINE IMMOBILISER>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2780 is not output.




OK

NG

3.READ VALUE USING TECHSTREAM (UNLOCK WARNING SWITCH)
3.READ VALUE USING TECHSTREAM (UNLOCK WARNING SWITCH)
a.

Use the Data List to check if the unlock warning switch is functioning properly.

Immobiliser
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Key SW Unlock warning switch signal / ON or OFF ON: Key is in ignition key cylinder
OFF: No key is in ignition key cylinder
-

OK:

ON (key is in ignition key cylinder) appears on the screen.




OK

NG

4.INSPECT UNLOCK WARNING SWITCH
4.INSPECT UNLOCK WARNING SWITCH
E146811E03
0.117,0.208 0.926,0.390 0.809,0.181 10 Not Pushed 0.197,0.964 0.531,1.145 0.334,0.181 10 Push

a.

Remove the unlock warning switch (see page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch is pushed Below 1 Ω
Switch is not pushed 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - BODY GROUND)

NG

REPLACE UNLOCK WARNING SWITCH

5.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - BODY GROUND)
B443041E01
0.563,1.281 0.906,1.531 0.344,0.25 0.135,0.125 2.385,0.5 2.25,0.375 10 false Front view of wire harness connector: (to Unlock Warning Switch) 0.625,1.313 0.865,1.5 0.24,0.188 10 false J18

a.

Disconnect the J18 switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J18-2 - Body ground Always Below 1 Ω




OK

6.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - TRANSPONDER KEY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - TRANSPONDER KEY ECU)
U151856E02
1.208,3.615 0.615,3.219 false 0.156,0.094 2.5,0.479 2.344,0.385 10 false Front view of wire harness connector: (to Unlock Warning Switch) 0.24,3.104 0.635,3.292 0.396,0.188 10 false KSW 0.146,2.198 2.49,2.583 2.344,0.385 10 false Front view of wire harness connector: (to Transponder Key ECU) 0.74,1.417 1.063,1.625 0.323,0.208 10 false J18 0.26,3.677 0.583,3.885 0.323,0.208 10 false J26

a.

Disconnect the J18 switch connector.


b.

Disconnect the J26 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J26-3 (KSW) - J18-1 Always Below 1 Ω
J26-3 (KSW) or J18-1 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR