Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM27M0U _58 Vehicle Interior _049157 METER / GAUGE / DISPLAY _0234436 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Oil Pressure Gauge Malfunction  


DESCRIPTION

The oil pressure sender detects the oil pressure generated when the engine is started. The combination meter determines that the engine is running when the engine speed is 400 rpm or more, and determines that the engine is cranking when the engine speed is 200 rpm or less. The oil pressure receiver gauge detects and indicates the oil pressure applied to the oil pressure sender.

WIRING DIAGRAM

E173476E04
2.31,1.78 2.660,1.928 0.350,0.149 10 ECM 3.077,1.513 4.705,1.683 1.628,0.170 10 CAN Communication Line 5.389,1.131 5.705,1.280 0.316,0.149 10 CPU 5.77,2.144 6.023,2.293 0.253,0.149 10 OIL 4.682,2.335 4.861,2.484 0.179,0.149 10 27 4.953,2.335 5.063,2.484 0.110,0.149 10 S 3.491,2.346 3.595,2.495 0.105,0.149 10 1 4.93,3.419 5.188,3.568 0.258,0.149 10 J28 4.93,3.587 6.141,3.736 1.211,0.149 10 Combination Meter 2.381,2.699 2.796,2.848 0.415,0.149 10 E11 2.381,2.851 4.139,3.000 1.758,0.149 10 Oil Pressure Sender Gauge

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN communication system DTC is not output A
CAN communication system DTC is output B



A

2.PERFORM ACTIVE TEST USING TECHSTREAM (OIL PRESSURE RECEIVER GAUGE)

B

2.PERFORM ACTIVE TEST USING TECHSTREAM (OIL PRESSURE RECEIVER GAUGE)
a.

Operate the Techstream according to the display and select "Active Test" (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter:
Tester Display Test Part Control Range Diagnostic Note
Oil Pressure Meter Operation Oil pressure receiver gauge OFF, LOW, 1/4, 1/2, 3/4 or HIGH Perform the test with the vehicle stopped and engine idling

OK:

Needle indication is normal.




OK

3.INSPECT OIL PRESSURE SENDER GAUGE

NG

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT OIL PRESSURE SENDER GAUGE
a.

Disconnect the E11 sender gauge connector.


A163798E08
1.646,1.073 2.156,1.073 true 1.104,2 1.719,2.188 0.615,0.188 10 false Test LED 0.094,0 2.615,0.365 2.521,0.365 10 false Component without harness connected: (Oil Pressure Sender Gauge) 2.219,0.979 2.333,1.156 0.115,0.177 10 false 1

b.

Apply battery positive (+) voltage to the sender gauge terminal through a test LED.


c.

Check that the LED does not illuminate when the engine is stopped.


d.

Check that the LED flashes when the engine is running. The number of flashes varies with engine speed.

OK:

LED flashes when engine is running.

LED does not illuminate when engine is stopped.


Result
Result Proceed to
LED operates correctly according to engine condition A
LED does not operate correctly according to engine condition (for 1UR-FE) B
LED does not operate correctly according to engine condition (for 3UR-FE) C
LED does not operate correctly according to engine condition (for 3UR-FBE) D



A

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - OIL PRESSURE SENDER GAUGE)

B

REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

C

REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

D

REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - OIL PRESSURE SENDER GAUGE)
E344837E01
0.76,1.615 1.146,1.823 0.385,0.208 4.042,1.656 4.427,1.865 0.385,0.208 2.135,1.76 2.583,2.177 false 0.208,0.156 2.417,0.521 2.208,0.365 10 false Rear view of wire harness connector: (to Combination Meter) 4.24,0.188 6.448,0.552 2.208,0.365 10 false Rear view of wire harness connector: (to Oil Pressure Sender Gauge) 0.833,1.625 1.104,1.813 0.271,0.188 10 false J28 4.104,1.667 4.375,1.854 0.271,0.188 10 false E11 2.625,2.146 2.813,2.333 0.188,0.188 10 false S

a.

Disconnect the J28 meter connector.


b.

Disconnect the E11 gauge connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J28-27 (S) - E11-1 Always Below 1 Ω
J28-27 (S) or E11-1 - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR