Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM27M0U _58 Vehicle Interior _049157 METER / GAUGE / DISPLAY _0234436 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Voltage Meter Malfunction  


DESCRIPTION

The voltmeter indicates the voltage applied to the IG+ terminal of the combination meter.

WIRING DIAGRAM

E146354E10
4.448,2.75 4.719,2.917 0.271,0.167 10 false J28 1.094,1.042 2.031,1.26 0.938,0.219 10 false from IG2 Relay 3.198,0.875 3.563,1.052 0.365,0.177 10 false MET 4.24,0.917 4.375,1.094 0.135,0.177 10 false 2 4.219,1.958 4.417,2.135 0.198,0.177 10 false 24 4.448,0.917 4.771,1.094 0.323,0.177 10 false IG+ 5.719,1.792 6.083,1.969 0.365,0.177 10 false VOLT 5.365,0.885 5.688,1.063 0.323,0.177 10 false CPU 4.438,1.958 4.76,2.135 0.323,0.177 10 false ES 4.438,2.927 5.729,3.135 1.292,0.208 10 false Combination Meter

PROCEDURE

1.INSPECT FUSE (MET)
a.

Remove the MET fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MET fuse Always Below 1 Ω




OK

2.PERFORM ACTIVE TEST USING TECHSTREAM (VOLTMETER)

NG

REPLACE FUSE

2.PERFORM ACTIVE TEST USING TECHSTREAM (VOLTMETER)
a.

Operate the Techstream according to the display and select "Active Test" (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter:
Tester Display Test Part Control Range Diagnostic Note
Volt Meter Operation Voltmeter OFF, 0 V, 3 V, 6V , 9 V, 12 V, 15 V or 18 V Perform the test with the vehicle stopped and engine idling

OK:

Needle indication is normal.




OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BATTERY AND BODY GROUND)

NG

REPLACE COMBINATION METER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BATTERY AND BODY GROUND)
U152713E02
2.115,1.438 2.417,1.667 true 2.458,1.052 2.26,1.365 true 0.083,0.021 2.427,0.406 2.344,0.385 10 false Rear view of wire harness connector: (to Combination Meter) 0.448,1.156 0.719,1.333 0.271,0.177 10 false J28 2.5,0.938 2.76,1.125 0.26,0.188 10 false IG+ 2.458,1.604 2.75,1.792 0.292,0.188 10 false ES

a.

Disconnect the J28 meter connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J28-24 (ES) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Switch Condition Specified Condition
J28-2 (IG+) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR