Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM27M0U _58 Vehicle Interior _049157 METER / GAUGE / DISPLAY _0234436 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is output when the combination meter detects the fuel sender gauge malfunction via the CAN.

DTC Code DTC Detection Condition Trouble Area
B1500 When combination meter detects fuel sender gauge malfunction
·

Harness or connector

·

Combination meter

·

Fuel sender gauge

·

Fuel suction with pump and gauge tube



WIRING DIAGRAM

B166182E06
4.444,3.05 4.722,3.238 0.278,0.188 10 J28 5.254,1.786 5.644,1.974 0.390,0.188 10 FUEL 4.185,0.757 4.398,0.945 0.213,0.188 10 26 4.185,1.302 4.398,1.490 0.213,0.188 10 25 2.604,1.302 2.772,1.490 0.168,0.188 10 2 3.476,1.302 3.644,1.490 0.168,0.188 10 3 4.456,0.757 4.822,0.945 0.366,0.188 10 L 4.456,1.302 4.822,1.490 0.366,0.188 10 E3 4.185,2.313 4.398,2.502 0.213,0.188 10 24 2.503,1.7 3.580,1.888 1.077,0.188 10 R6*1, R19*2 2.503,1.9 3.825,2.088 1.322,0.188 10 Fuel Sender Gauge 4.456,2.313 4.822,2.502 0.366,0.188 10 ES 4.444,3.232 5.723,3.420 1.279,0.188 10 Combination Meter 0.229,3.113 1.803,3.249 1.575,0.136 10 *1: except 3UR-FBE 0.229,3.389 1.803,3.526 1.575,0.136 10 *2: for 3UR-FBE

PROCEDURE

1.READ VALUE USING TECHSTREAM (FUEL SENDER GAUGE)
a.

Operate the Techstream according to the display and select the "Data List" (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Fuel Level Fuel sender gauge (main) input signal/Min.: 0, Max.: 127.5 Fuel sender input value Unit: L

OK:

Fuel value displayed on Techstream is almost same as needle indication




OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SUCTION WITH PUMP AND GAUGE TUBE AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SUCTION WITH PUMP AND GAUGE TUBE AND BODY GROUND)
U152771E01
0.189,0.099 2.534,0.484 2.345,0.385 10 Rear view of wire harness connector: (to Combination Meter) 0.052,2.478 2.738,2.863 2.687,0.385 10 Front view of wire harness connector: (to Fuel Suction with Pump and Gauge Tube) 2.112,2.012 2.324,2.176 0.212,0.165 10 E3 2.424,1.923 2.685,2.088 0.261,0.165 10 ES 0.476,1.27 0.770,1.435 0.294,0.165 10 J28 1.929,1.96 2.063,2.125 0.134,0.165 10 L 2.145,1.47 2.529,1.9 false 2.014,1.466 1.948,1.939 false 2.065,1.455 2.223,2.006 false 0.453,3.447 0.652,3.593 0.199,0.147 10 R6 0.966,3.447 1.165,3.593 0.199,0.147 10 *1 0.966,3.848 1.165,3.995 0.199,0.147 10 *2 0.408,3.848 0.680,3.995 0.273,0.147 10 R19 0.081,4.275 1.656,4.411 1.575,0.136 10 *1: except 3UR-FBE 1.78,4.275 2.855,4.411 1.075,0.136 10 *2: for 3UR-FBE

a.

Disconnect the J28 meter connector.


b.

Disconnect the R6*1 or R19*2 gauge connector.

*1: except 3UR-FBE

*2: for 3UR-FBE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except 3UR-FBE
Tester Connection Condition Specified Condition
J28-26 (L) - R6-2 Always Below 1 Ω
J28-25 (E3) - R6-3
J28-24 (ES) - Body ground
J28-26 (L) or R6-2 - Body ground Always 10 kΩ or higher

for 3UR-FBE
Tester Connection Condition Specified Condition
J28-26 (L) - R19-2 Always Below 1 Ω
J28-25 (E3) - R19-3
J28-24 (ES) - Body ground
J28-26 (L) or R19-2 - Body ground Always 10 kΩ or higher




OK

3.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT FUEL SENDER GAUGE ASSEMBLY
E282500E02
1.406,2.573 0.677,2.573 false 1.167,4.354 0.667,4.354 false 0.281,0.271 2.792,0.677 2.51,0.406 10 false Component without harness connected: (Fuel Sender Gauge) 0.51,4.302 0.635,4.479 0.125,0.177 10 false E 0.521,2.521 0.646,2.708 0.125,0.188 10 false F


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Float level is F (upper) 12 to 18 Ω
Float level is E (lower) 405 to 415 Ω


Result
Result Proceed to
OK A
NG (for 1UR-FE) B
NG (for 3UR-FE) C
NG (for 3UR-FBE) D



A

4.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

B

REPLACE FUEL SENDER GAUGE ASSEMBLY

C

REPLACE FUEL SENDER GAUGE ASSEMBLY

D

REPLACE FUEL SENDER GAUGE ASSEMBLY

4.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
U152786E02
0.094,0.052 2.677,0.438 2.583,0.385 10 false Component without harness connected: (Fuel Suction with Pump and Gauge Tube) 0.417,1.427 0.563,1.604 0.146,0.177 10 false A 0.375,3.771 0.521,3.958 0.146,0.188 10 false B


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A2 - B2 Always Below 1 Ω
A3 - B1


Result
Result Proceed to
OK A
NG (for 1UR-FE) B
NG (for 3UR-FE) C
NG (for 3UR-FBE) D



A

REPLACE COMBINATION METER ASSEMBLY

B

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

C

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

D

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY