Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049158 NAVIGATION / MULTI INFO DISPLAY _0234440 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Radio Broadcast cannot be Received or Poor Reception  


PROCEDURE

1.CHECK IF RADIO AUTO-SEARCH FUNCTIONS PROPERLY
a.

Check the radio automatic station search function by activating it.

OK:

Automatic station search function stops on a station.




OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

OK:

Optional components are installed.


NOTICE:

Do not remove optional components without permission of the customer.




OK

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

NG

3.CHECK RADIO ANTENNA
3.CHECK RADIO ANTENNA
a.

Remove the pull top antenna pole sub-assembly from the fender antenna assembly.


b.

Place the tip of a screwdriver on the antenna and check that noise is heard from the speakers.

OK:

Noise occurs.


Result
Result Proceed to
OK (for Column Shift Type) A
OK (for Floor Shift Type) B
NG C



A

B

C

4.CHECK NAVIGATION RECEIVER ASSEMBLY (ANTENNA)
4.CHECK NAVIGATION RECEIVER ASSEMBLY (ANTENNA)
a.
E276819

Remove the antenna connector from the navigation receiver assembly.


b.

Turn the ignition switch to ACC with the navigation receiver assembly connector connected.


c.

Turn on the radio and turn into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise occurs.


Result
Result Proceed to
OK A
NG (for Column Shift Type) B
NG (for Floor Shift Type) C



A

5.INSPECT NAVIGATION RECEIVER ASSEMBLY

B

C

5.INSPECT NAVIGATION RECEIVER ASSEMBLY
a.
E277921E01
1.063,0.781 1.281,0.781 1.281,0.781 1.531,1.042 true 2.333,0.635 2.083,0.635 2.083,0.635 1.833,0.885 true 2.354,1.583 2.104,1.583 2.104,1.583 1.833,1.271 true 0.677,0.698 1.208,0.885 0.531,0.188 10 false ANT+ 2.375,0.552 2.906,0.74 0.531,0.188 10 false 2 2.396,1.5 2.927,1.688 0.531,0.188 10 false 4

Disconnect the J151 navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Ignition switch ACC, radio switch on and FM or AM selected 11 to 14 V


Result
Result Proceed to
OK A
NG (for Column Shift Type) B
NG (for Floor Shift Type) C



A

6.CHECK PULL TOP ANTENNA POLE SUB-ASSEMBLY

B

C

6.CHECK PULL TOP ANTENNA POLE SUB-ASSEMBLY
a.

Check that the pull top antenna pole sub-assembly is securely installed (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>REMOVAL).

OK:

The pull top antenna pole sub-assembly is installed properly.




OK

7.CHECK FENDER ANTENNA ASSEMBLY

NG

REINSTALL PULL TOP ANTENNA POLE SUB-ASSEMBLY

7.CHECK FENDER ANTENNA ASSEMBLY
a.

Replace the fender antenna assembly and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA>REMOVAL).

OK:

Radio broadcasts can be received normally.


Result
Result Proceed to
OK A
NG (for Column Shift Type) B
NG (for Floor Shift Type) C



A

END (FENDER ANTENNA ASSEMBLY IS DEFECTIVE)

B

C