Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTUITIVE PARKING ASSIST SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234441 INTUITIVE PARKING ASSIST SYSTEM J

PARK ASSIST / MONITORING  INTUITIVE PARKING ASSIST SYSTEM  Park / Neutral Position Switch Circuit  


DESCRIPTION

This circuit sends the park/neutral position switch assembly signals to the clearance warning ECU assembly.

WIRING DIAGRAM

E280658E01
5.366,2.282 5.846,2.443 0.480,0.161 10 J35 5.506,1.764 5.986,1.925 0.480,0.161 10 RL 5.506,0.937 5.986,1.098 0.480,0.161 10 PL 5.226,1.68 5.451,1.841 0.225,0.161 10 21 3.194,1.302 3.674,1.462 0.480,0.161 10 RB 2.989,1.218 3.140,1.378 0.151,0.161 10 2 5.268,0.853 5.465,1.014 0.198,0.161 10 6 4.035,1.764 4.288,1.925 0.253,0.161 10 RL 4.035,0.937 4.288,1.098 0.253,0.161 10 PL 4.343,1.68 4.569,1.841 0.225,0.161 10 1 4.343,0.853 4.569,1.014 0.225,0.161 10 6 5.366,2.454 6.661,2.807 1.295,0.353 10 Clearance Warning ECU Assembly 3.054,2.282 3.534,2.443 0.480,0.161 10 D35 1.933,1.47 2.756,1.630 0.823,0.161 10 BK/UP LP*1 1.933,1.75 2.756,1.911 0.823,0.161 10 LH-IG*2 0.126,1.302 1.560,1.462 1.434,0.161 10 from IG1 No.2 Relay*1 0.126,1.582 1.560,1.742 1.434,0.161 10 from IG No.1 Relay*2 0.266,3.123 2.126,3.284 1.860,0.161 10 *1: for Floor Shift Type 0.266,3.403 2.126,3.564 1.860,0.161 10 *2: for Column Shift Type 3.054,2.454 4.488,2.807 1.434,0.353 10 Park/Neutral Position Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CLEARANCE WARNING ECU ASSEMBLY
a.
U152819E02
2.188,0.969 2.635,0.396 2.635,0.396 2.823,0.396 true 2.094,1.177 2.542,1.771 2.542,1.771 2.729,1.771 true 1.604,0.229 1.948,0.396 0.344,0.167 10 false J35 0.115,0.083 0.458,0.25 0.344,0.167 10 false *a 2.865,0.313 3.208,0.479 0.344,0.167 10 false PL 2.781,1.688 3.125,1.854 0.344,0.167 10 false RL

Disconnect the clearance warning ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J35-6 (PL) - Body ground Ignition switch ON, shift lever in P 11 to 14 V
Ignition switch ON, shift lever not in P Below 1 V
J35-21 (RL) - Body ground Ignition switch ON, shift lever in R 11 to 14 V
Ignition switch ON, shift lever not in R Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the D35 park/neutral position switch assembly connector.


b.

Disconnect the J35 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D35-6 (PL) - J35-6 (PL) Always Below 1 Ω
D35-1 (RL) - J35-21 (RL) Always Below 1 Ω
D35-6 (PL) - Body ground Always 10 kΩ or higher
D35-1 (RL) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
U152736E02
1.844,1.323 2.469,0.854 2.469,0.854 2.719,0.854 true 0.115,0.063 0.375,0.271 0.26,0.208 10 false *a 1.604,0.531 1.885,0.698 0.281,0.167 10 false D35 2.771,0.76 3.031,0.927 0.26,0.167 10 false RB

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D35-2 (RB) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)

HINT:

*: Park/neutral position switch assembly replacement procedure:





OK

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY*

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR