Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTUITIVE PARKING ASSIST SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234441 INTUITIVE PARKING ASSIST SYSTEM J

PARK ASSIST / MONITORING  INTUITIVE PARKING ASSIST SYSTEM  Clearance Warning ECU Power Source Circuit  


DESCRIPTION

This circuit is the power source circuit to operate the clearance warning ECU assembly.

WIRING DIAGRAM

E280652E02
5.406,2.635 5.833,2.833 0.427,0.198 10 false J35 5.75,2.219 6.177,2.417 0.427,0.198 10 false E 5.75,0.708 6.177,0.906 0.427,0.198 10 false IG 5.49,0.615 5.708,0.813 0.219,0.198 10 false 11 4.042,0.74 4.406,0.938 0.365,0.198 10 false ECU 2.896,0.708 3.26,0.906 0.365,0.198 10 false IG 1.708,0.865 2.604,1.063 0.896,0.198 10 false ECU-IG No.1 0.427,0.74 1.323,1.167 0.896,0.427 10 false from IG No.1 Relay 2.896,1.271 3.26,1.469 0.365,0.198 10 false E 4.427,0.615 4.646,0.813 0.219,0.198 10 false 3 2.688,0.604 2.906,0.802 0.219,0.198 10 false 6 2.698,1.146 2.917,1.344 0.219,0.198 10 false 7 5.49,2.125 5.708,2.323 0.219,0.198 10 false 16 5.406,2.802 7.031,3.177 1.625,0.375 10 false Clearance Warning ECU Assembly 2.813,1.688 3.24,1.885 0.427,0.198 10 false J125 2.813,1.865 4.438,2.24 1.625,0.375 10 false Back Sonar or Clearance Sonar Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
U151873E02
2.021,1.635 1.927,1.99 1.927,1.99 1.823,1.99 true 2.24,1.635 2.344,1.99 2.344,1.99 2.438,1.99 true 0.115,0.073 2.51,0.385 2.396,0.313 10 false *a 1.552,0.583 1.896,0.75 0.344,0.167 10 false J125 1.625,1.917 1.875,2.073 0.25,0.156 10 false IG 2.51,1.906 2.76,2.063 0.25,0.156 10 false E

Disconnect the back sonar or clearance sonar switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J125-6 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J125-7 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Back Sonar or Clearance Sonar Switch Assembly)


OK

2.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
a.

Remove the back sonar or clearance sonar switch assembly (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>REMOVAL).


b.

Inspect the back sonar or clearance sonar switch assembly (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY AND BODY GROUND)

NG

REPLACE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY AND BODY GROUND)
a.

Disconnect the J35 clearance warning ECU assembly connector.


b.

Disconnect the J125 back sonar or clearance sonar switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J35-11 (IG) - J125-3 (ECU) Always Below 1 Ω
J35-11 (IG) - Body ground Always 10 kΩ or higher
J35-16 (E) - Body ground Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR