Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2015.08–2016.08
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234450 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  OPERATION CHECK  


BLIND SPOT MONITOR BEAM AXIS INSPECTION


a.

Procedure to enter Test Mode

i.

Connect the Techstream to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the blind spot monitor main switch assembly (warning canceling switch assembly) on.


iv.

Turn the Techstream on.


v.

Switch the blind spot monitor sensor to Test Mode using the Techstream. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master beam axis inspection or BSM Slave beam axis inspection.


vi.

Finish Test Mode.




BLIND SPOT MONITOR BEAM AXIS CONFIRMATION


a.

When performing the blind spot monitor beam axis confirmation, move the vehicle to a place where the space shown in the illustration can be secured.

U131939E02
0.094,0.083 0.771,0.271 0.677,0.188 12 false LH Side: 3.885,0.083 4.781,0.271 0.896,0.188 12 false RH Side: 0.99,4.01 1.917,4.208 0.927,0.198 10 false 6 m (19.69 ft.) 2.125,4.031 2.979,4.229 0.854,0.198 10 false 3 m (9.85 ft.) 4.281,4.031 5.135,4.229 0.854,0.198 10 false 3 m (9.85 ft.) 0.396,0.698 1.302,0.896 0.906,0.198 10 false 8 m (26.25 ft.) 5.813,0.719 6.719,0.917 0.906,0.198 10 false 8 m (26.25 ft.) 3.135,1.833 4,2.021 0.865,0.188 10 false Rear Bumper 1.438,0.396 2.656,0.583 1.219,0.188 10 false Left side of vehicle 4.552,0.385 5.865,0.573 1.313,0.188 10 false Right side of vehicle 1.302,4.365 2.385,4.563 1.083,0.198 10 false : Inspection Area 5.333,4.021 6.26,4.219 0.927,0.198 10 false 6 m (19.69 ft.) 0.469,1.073 1.292,1.281 0.823,0.208 10 false 2 m (6.57 ft.) 5.854,1.083 6.677,1.292 0.823,0.208 10 false 2 m (6.57 ft.)

NOTICE:
·

Perform this inspection on level ground.

·

Make sure that there are no metal objects around the vehicle or on the ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.

·

Do not place an object other than the reflector (such as a large metallic object) in or allow people to enter the inspection area (W 9 m (29.53 ft.) x L 10 m (32.81 ft.) x H 4 m (13.13 ft.)) shown in the illustration.

·

Check that DTC C1ABB and DTC C1ABC are not output.




b.

Place the reflector.

i.

Hang a string (with weight) from the center of the vehicle's rear emblem. Mark the vehicle's rear center point on the ground. Repeat for the front of the vehicle. (mark (A) and (B))


ii.
E238824E12
1.427,1.271 1.198,1.552 false 3.01,1.271 3.167,1.635 false 0.635,1.271 1.094,0.458 false 1.094,0.448 1.292,0.448 false 1.333,0.354 2.542,0.51 1.208,0.156 10 false Vehicle center line 1.104,1.531 1.26,1.688 0.156,0.156 10 false A 3.188,1.625 3.344,1.781 0.156,0.156 10 false B

Draw a vehicle center line so that it passes through mark (A) and (B) (front and rear center points).


iii.
E238823E44
0.5,1.708 0.354,1.271 false 1.292,1.688 1.438,1.281 false 3.177,1.677 3.01,1.271 false 1.229,1.729 1.51,1.917 0.281,0.188 10 false A 3.167,1.729 3.365,1.969 0.198,0.24 10 false B 0.563,1.698 0.792,1.885 0.229,0.188 10 false C 0.323,0.198 2.323,0.417 2,0.219 10 false 684 to 704 mm (2.24 to 2.31 ft.)

Mark the position on the center line 684 to 704 mm (2.24 to 2.31 ft.) behind the rear bumper. (Mark (C))


iv.
E238825E18
1.708,3.771 2.083,3.385 2.083,3.385 2.25,3.385 false 0.302,3.479 1.469,3.688 1.167,0.208 10 false 300 mm (11.8 in.) 2.313,3.302 2.542,3.479 0.229,0.177 10 false C 0.281,0.115 1.177,0.271 0.896,0.156 10 false Vehicle front 0.313,3.917 1.479,4.125 1.167,0.208 10 false 300 mm (11.8 in.)

Prepare 2 pieces of string of 600 mm (1.97 ft.) in length and secure the end of each string at a point 300 mm (11.8 in.) from mark (C) as shown in the illustration.


v.

Pull the end of each string and mark the position where each string meets on both the left and right side (marks (D) and (E)).

E238826E13
5.083,1.844 5.427,1.313 5.427,1.313 5.583,1.313 false 5.469,2.052 5.604,1.802 5.604,1.802 5.708,1.802 false 5.198,2.208 5.438,2.354 5.438,2.354 5.656,2.354 false 1.74,1.823 1.375,1.198 1.375,1.198 1.229,1.198 false 1.323,2.052 1.198,1.781 1.198,1.781 1.104,1.781 false 1.635,2.229 1.417,2.365 1.417,2.365 1.177,2.365 false 2,2.052 2.135,1.844 2.135,1.844 2.24,1.844 false 4.792,2.063 4.5,1.563 4.5,1.563 4.406,1.563 false 4.125,2.063 4.042,2.219 4.042,2.219 3.906,2.219 false 2,0.375 2.292,0.135 2.292,0.135 2.448,0.135 false 4.792,0.365 5.083,0.125 5.083,0.125 5.24,0.125 false 5.781,1.719 6.865,1.917 1.083,0.198 12 false E 0.833,1.104 1.281,1.302 0.448,0.198 10 false String 0.927,1.698 1.073,1.896 0.146,0.198 12 false D 2.292,1.76 2.49,1.958 0.198,0.198 12 false C 3.74,2.135 3.885,2.333 0.146,0.198 12 false D 4.24,1.49 4.438,1.688 0.198,0.198 12 false C 0.094,0.073 1.427,0.385 1.333,0.313 12 false Vehicle rear: 0.771,2.271 1.219,2.469 0.448,0.198 10 false String 5.635,1.229 6.083,1.427 0.448,0.198 10 false String 5.729,2.26 6.177,2.458 0.448,0.198 10 false String 2.51,0.063 3.698,0.375 1.188,0.313 10 false Vehicle center line 5.313,0.063 6.542,0.375 1.229,0.313 10 false Vehicle center line


vi.
E238827E15
2.313,3.927 2.448,3.646 2.448,3.646 2.573,3.646 false 1.063,3.927 0.948,4.156 0.948,4.156 0.813,4.156 false 1.688,0.521 2.031,0.26 2.031,0.26 2.177,0.26 false 1.885,3.927 2.094,4.25 2.094,4.25 2.219,4.25 false 2.615,3.552 2.792,3.75 0.177,0.198 12 false E 0.646,4.073 0.792,4.271 0.146,0.198 12 false D 0.281,0.115 1.125,0.313 0.844,0.198 10 false Vehicle front 2.292,0.188 3.188,0.5 0.896,0.313 10 false Vehicle center line 2.302,4.156 2.823,4.417 0.521,0.26 10 false Line P

Draw a line (P) so that it passes through mark (D) and (E) and is perpendicular to the vehicle center line.


vii.

Set the reflector at the position (Z) shown in the illustration below.

SST
09870-60000  (09870-60010)
09870-60040  

E233794E32
0.688,3.25 1.094,2.938 false 6.25,3.104 5.917,2.917 false 2.688,2.208 2.917,1.781 false 2.917,1.781 3.052,1.781 false 4.385,2.198 4.135,1.781 false 4.135,1.781 3.979,1.781 false 5.313,2.563 5.552,1.781 false 5.552,1.781 5.698,1.781 false 2.01,2.385 1.74,1.781 false 1.74,1.781 1.573,1.781 false 2.563,2.875 2.719,3.167 false 2.719,3.167 2.771,3.167 false 4.542,2.854 4.365,3.146 false 4.365,3.146 4.302,3.146 false 1.177,2.865 1.052,2.354 false 1.052,2.354 0.979,2.354 false 5.833,2.833 5.948,2.344 false 5.948,2.344 6.01,2.344 false 0.5,0.094 1.24,0.354 0.74,0.26 12 false LH Side: 3.448,0.083 4.198,0.344 0.75,0.26 12 false RH Side: 4.104,0.313 5.313,0.479 1.208,0.167 10 false Vehicle center line 3.021,2.302 4.031,2.677 1.01,0.375 10 false 684 to 704 mm (2.24 to 2.31 ft.) 0.865,2.271 1.021,2.458 0.156,0.188 10 false Z 6.063,2.26 6.188,2.448 0.125,0.188 10 false Z 0.323,3.26 0.917,3.427 0.594,0.167 10 false Reflector 6.125,3.125 6.719,3.292 0.594,0.167 10 false Reflector 1.76,0.302 2.969,0.469 1.208,0.167 10 false Vehicle center line 3.146,1.698 4.021,1.865 0.875,0.167 10 false Rear bumper 1.229,3.177 2.406,3.604 1.177,0.427 10 false 3255 to 3275 mm (10.68 to 10.74 ft.) 5.75,1.698 6.99,1.906 1.24,0.208 10 false 3338 mm (10.95 ft.) 0.333,1.688 1.573,1.927 1.24,0.24 10 false 3338 mm (10.95 ft.) 2.823,3.083 3.313,3.25 0.49,0.167 10 false Line P 3.854,3.063 4.344,3.229 0.49,0.167 10 false Line P 4.74,3.135 5.906,3.563 1.167,0.427 10 false 3255 to 3275 mm (10.68 to 10.74 ft.)

NOTICE:
·
E238830E38
0.292,1.385 0.833,1.781 0.542,0.396 10 false 629 mm (2.06 ft.)

Set the reflector so that its center is 629 mm (2.06 ft.) above the ground.

·
E238829E14
1.99,0.677 2.479,1.302 false 1.865,1.313 3.094,1.656 1.229,0.344 10 false Center of triangular pyramid

The center of triangular pyramid is the reference point for the setting position and angle.

·

Set the reflector as shown in the illustration so that its center of triangular pyramid faces the blind spot monitor sensor.

·

Perform the operation as precisely as possible.





c.

Perform the blind spot monitor beam axis display.

i.

Connect the Techstream to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the blind spot monitor main switch assembly (warning canceling switch assembly) on.


iv.

Turn the Techstream on.


v.

Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master beam axis display or BSM Slave beam axis display.


vi.

Check the results displayed for the BSM beam axis display.

Allowable Range:
Item Blind Spot Monitor Sensor RH (Master) Blind Spot Monitor Sensor LH (Slave)
Angle -3.6 to +3.6° -3.6 to +3.6°
Distance 2.0 to 3.0 m
(6.57 to 9.85 ft.)
2.0 to 3.0 m
(6.57 to 9.85 ft.)


HINT:

If the results are outside the allowable range, try again as the reflector setting position may be incorrect or a metal object may exist near the detection area.



vii.

Perform the blind spot monitor beam axis adjustment using the Techstream. Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master beam axis adjustment or BSM Slave beam axis adjustment.

HINT:

When values on the axis display are in the allowable range, performing this adjustment compensates the values to the normal value.





BLIND SPOT MONITOR INSTALLATION CONDITION INSPECTION


NOTICE:
·

Perform this inspection on level ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.




b.

Attach a jig similar to the one shown in the illustration to the outward facing surface of the blind spot monitor sensor and check that the blind spot monitor sensor is perpendicular to the floor surface or within the allowable range.

E233717E03
5.917,3.958 5.917,3.417 false 5.917,3.417 6.063,3.417 false 1.948,3.583 1.948,2.448 false 2.302,2.115 2.979,3.5 false 5.052,1.208 5.583,0.615 false 5.583,0.615 5.729,0.615 false 4.615,3.25 4.875,3.25 false 2.979,3.5 3.094,3.5 false 6.083,3.344 6.917,3.531 0.833,0.188 10 Floor surface 1.188,3.583 2.906,3.75 1.719,0.167 10 Blind Spot Monitor Sensor 3.125,3.438 4.813,3.646 1.688,0.208 10 Outward facing surface 0.156,0.063 2.281,0.448 2.125,0.385 12 Rear view of vehicle (RH): 5.76,0.552 6.208,0.792 0.448,0.24 10 Jig 4.906,3.188 5.479,3.427 0.573,0.24 10 Weight

E233716E20
1.698,0.844 3.042,1.385 1.344,0.542 10 false Hold this side against the blind spot monitor sensor RH. 1.365,2.823 2.833,3.24 1.469,0.417 10 false Position where string is to be secured 2.708,4.146 2.854,4.323 0.146,0.177 10 false A 3.948,4.135 4.094,4.313 0.146,0.177 10 false B 5.344,3.188 5.885,3.635 0.542,0.448 10 false 100 mm (3.94 in.) 1.01,6.177 2.271,6.385 1.26,0.208 10 false : Allowable range 0.25,0.198 0.802,0.438 0.552,0.24 12 false Jig: 4.146,0.844 5.542,1.375 1.396,0.531 10 false Hold this side against the blind spot monitor sensor LH. 3.271,1.698 3.552,1.896 0.281,0.198 10 false Top 1.542,4.99 1.688,5.167 0.146,0.177 10 false + 5.146,4.979 5.292,5.156 0.146,0.177 10 false -

Standard
A B
Blind spot monitor sensor RH 8 mm
(0.315 in.)
-8 mm
(-0.315 in.)
Blind spot monitor sensor LH 8 mm
(0.315 in.)
-8 mm
(-0.315 in.)


c.
E224437E26
1.229,3.615 1.469,4.021 false 2.521,0.635 2.917,1.167 false 0.781,3.573 0.729,3.854 false 0.552,3.833 0.271,3.906 false 0.271,3.906 0.271,4.281 false 1.396,2 1.542,1.677 1.542,1.677 1.625,1.677 false 1.469,4.021 1.563,4.021 false 0.094,0.094 1.448,0.302 1.354,0.208 12 false Vehicle rear (LH): 1.344,0.542 2.51,0.854 1.167,0.313 10 false Vehicle center line 1.615,3.938 2.24,4.104 0.625,0.167 10 false Stud bolt 1.521,1 2.313,1.167 0.792,0.167 10 false Vehicle front 0.688,3.823 0.854,4.073 0.167,0.25 10 false y 1.958,3.719 2.719,3.885 0.76,0.167 10 false Vehicle rear 0.083,4.302 2.458,4.51 2.375,0.208 10 false Line parallel to the vehicle center line 1.802,2.385 2.333,2.573 0.531,0.188 10 false 104 mm 1.688,1.594 2.729,1.99 1.042,0.396 10 false Stud bolt center line 1.802,2.594 2.49,2.781 0.688,0.188 10 false (4.09 in.)

Using the sensor installation stud bolt center lines as a reference, check that the stud bolts are as shown in the illustration.

Standard:
Dimension Specified Value
y 29 to 42 mm
(1.15 to 1.65 in.)