Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234450 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB1  Short to +B in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a +B short in the blind spot monitor indicator LH.

DTC Code DTC Detection Condition Trouble Area
C1AB1 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage applied to the indicator is high for a certain amount of time even though the blind spot monitor sensor is not outputting voltage to the indicator.
·

Harness or connector

·

Blind spot monitor sensor LH

·

Outer rear view mirror assembly LH

·

Outer rear view mirror sub-assembly LH



WIRING DIAGRAM

E221720E42
3.042,1.24 3.594,1.469 0.552,0.229 10 false BSL+ 0.865,2.167 1.198,2.323 0.333,0.156 10 false B 0.844,2.344 3.375,2.729 2.531,0.385 10 false Outer Rear View Mirror Sub-assembly LH (Blind Spot Monitor Indicator LH) 0.833,3.406 1.167,3.563 0.333,0.156 10 false N5 0.823,3.583 3.167,3.792 2.344,0.208 10 false Outer Rear View Mirror Assembly LH 5.531,3.385 5.865,3.542 0.333,0.156 10 false S5 5.531,3.563 6.719,3.906 1.188,0.344 10 false Blind Spot Monitor Sensor LH 2.552,1.25 2.76,1.427 0.208,0.177 10 false 7 2.375,1.344 2.521,1.5 0.146,0.156 10 false + 5.385,1.24 5.563,1.396 0.177,0.156 10 false 4 5.573,1.354 5.948,1.51 0.375,0.156 10 false OMIL 2.385,1.823 2.677,2.063 0.292,0.24 10 false - 2.552,1.719 2.729,1.875 0.177,0.156 10 false 5 3.521,1.24 4.198,1.438 0.677,0.198 10 false 9*1, 18*2 3.521,1.719 3.76,1.896 0.24,0.177 10 false 5 3.052,1.729 3.438,2.021 0.385,0.292 10 false MLP- 0.167,4.198 1.156,4.417 0.99,0.219 10 false *1: w/ Memory 0.167,4.427 1.156,4.646 0.99,0.219 10 false *2: w/o Memory

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR LH CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR INDICATOR LH CIRCUIT)
a.
U152813E02
1.875,1.156 2.375,0.708 2.375,0.708 2.615,0.708 true 1.635,0.302 1.906,0.5 0.271,0.198 10 false S5 2.667,0.635 3.083,0.792 0.417,0.156 10 false OMIL 0.094,0.052 0.365,0.25 0.271,0.198 10 false *a

Disconnect the blind spot monitor sensor LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S5-4 (OMIL) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)



OK

NG

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER REAR VIEW MIRROR ASSEMBLY LH)
3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.
U152813E02
1.875,1.156 2.375,0.708 2.375,0.708 2.615,0.708 true 1.635,0.302 1.906,0.5 0.271,0.198 10 false S5 2.667,0.635 3.083,0.792 0.417,0.156 10 false OMIL 0.094,0.052 0.365,0.25 0.271,0.198 10 false *a

Disconnect the blind spot monitor sensor LH connector.


b.

Disconnect the N5 outer rear view mirror assembly LH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S5-4 (OMIL) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)



OK

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH)
a.
U152813E02
1.875,1.156 2.375,0.708 2.375,0.708 2.615,0.708 true 1.635,0.302 1.906,0.5 0.271,0.198 10 false S5 2.667,0.635 3.083,0.792 0.417,0.156 10 false OMIL 0.094,0.052 0.365,0.25 0.271,0.198 10 false *a

Disconnect the blind spot monitor sensor LH connector.


b.

Disconnect the B outer rear view mirror sub-assembly LH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S5-4 (OMIL) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)



OK

REPLACE OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH