Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234450 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  U0232  Lost Communication with Blind Spot Monitor Slave Module  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH judges that there is a communication problem with the blind spot monitor sensor LH.

DTC Code DTC Detection Condition Trouble Area
U0232 The blind spot monitor sensor RH cannot receive signals from the blind spot monitor sensor LH.
·

CAN communication Line

·

Harness or connector

·

Blind spot monitor sensor LH

·

Blind spot monitor sensor RH



WIRING DIAGRAM

E233765E62
0.885,4.021 2.646,4.219 1.76,0.198 10 false : CAN Communication Line 3.042,2.635 3.74,2.885 0.698,0.25 10 false BLGD 2.792,2.5 2.969,2.667 0.177,0.167 10 false 10 3.063,1.229 3.448,1.5 0.385,0.271 10 false BLB 2.865,1.104 2.969,1.271 0.104,0.167 10 false 5 3.542,1.625 4.156,1.823 0.615,0.198 10 false CA2P 4.01,1.438 4.135,1.604 0.125,0.167 10 false 1 3.531,1.958 4.146,2.156 0.615,0.198 10 false CA2N 4.01,1.792 4.135,1.958 0.125,0.167 10 false 6 5.406,1.583 6.052,1.865 0.646,0.281 10 false CA2P 5.229,1.438 5.354,1.604 0.125,0.167 10 false 1 5.417,1.938 6.094,2.177 0.677,0.24 10 false CA2N 5.198,3.198 5.49,3.448 0.292,0.25 10 false S6 5.208,3.365 6.406,3.719 1.198,0.354 10 false Blind Spot Monitor Sensor RH 2.833,3.198 3.167,3.406 0.333,0.208 10 false S5 2.844,3.375 4.021,3.729 1.177,0.354 10 false Blind Spot Monitor Sensor LH 5.229,1.792 5.354,1.958 0.125,0.167 10 false 6 1.719,1.385 2.615,1.583 0.896,0.198 10 false ECU-IG No.1 0.26,1.24 1.104,1.635 0.844,0.396 10 false from IG No.1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling switch assembly) is on.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the S6 blind spot monitor sensor RH connector.


b.

Disconnect the S5 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S6-1 (CA2P) - S5-1 (CA2P) Always Below 1 Ω
S6-6 (CA2N) - S5-6 (CA2N) Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CAN LINE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - BATTERY AND BODY GROUND)
a.
U152814E02
2.031,1.135 2.396,0.688 2.396,0.688 2.635,0.688 true 1.99,1.385 2.354,1.927 2.354,1.927 2.594,1.927 true 1.604,0.302 1.875,0.5 0.271,0.198 10 false S5 2.667,0.615 3.083,0.771 0.417,0.156 10 false BLB 0.104,0.063 0.375,0.26 0.271,0.198 10 false *a 2.646,1.844 3.063,2 0.417,0.156 10 false BLGD

Disconnect the blind spot monitor sensor LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S5-5 (BLB) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S5-10 (BLGD) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


OK

3.CHECK BLIND SPOT MONITOR SENSOR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK BLIND SPOT MONITOR SENSOR LH
a.

Replace the blind spot monitor sensor LH with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SENSOR>REMOVAL).



c.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (BLIND SPOT MONITOR SENSOR LH IS DEFECTIVE)

NG