Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234450 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1ABD  Short to +B in Buzzer  C1ABE  Short to GND or Open in Buzzer  


DESCRIPTION

·

DTC C1ABD is stored when the blind spot monitor sensor LH detects a +B short in rear cross traffic alert buzzer (blind spot monitor buzzer) circuit.

·

DTC C1ABE is stored when the blind spot monitor sensor LH detects a ground short or open in rear cross traffic alert buzzer (blind spot monitor buzzer) circuit.


DTC Code DTC Detection Condition Trouble Area
C1ABD

Both of the following conditions are met:

·

Blind spot monitor main switch assembly (warning canceling switch assembly) is on with ignition switch ON.

·

The blind spot monitor sensor is not sending voltage to the buzzer but the buzzer receives voltage above a specified level for a specified period of time.



·

Blind spot monitor sensor LH

·

Rear cross traffic alert buzzer (blind spot monitor buzzer)

·

Harness or connector


C1ABE

Both of the following conditions are met:

·

Blind spot monitor main switch assembly (warning canceling switch assembly) is on with ignition switch ON.

·

The current flowing to the buzzer is below a specified value when buzzer operation voltage is being sent to the buzzer.



·

Blind spot monitor sensor LH

·

Rear cross traffic alert buzzer (blind spot monitor buzzer)

·

Harness or connector



WIRING DIAGRAM

E254403E58
0.292,1.021 1.698,1.219 1.406,0.198 10 false from IG No.1 Relay 3.521,1.021 3.813,1.219 0.292,0.198 10 false BZP 3.177,1.313 3.521,1.51 0.344,0.198 10 false P19 3.177,1.479 5.115,1.885 1.938,0.406 10 false Rear Cross Traffic Alert Buzzer (Blind Spot Monitor Buzzer) 5.604,1.958 5.896,2.156 0.292,0.198 10 false S5 5.615,2.125 6.813,2.49 1.198,0.365 10 false Blind Spot Monitor Sensor LH 4.323,1.021 4.656,1.219 0.333,0.198 10 false BZN 3.333,0.906 3.479,1.083 0.146,0.177 10 false 1 5.646,1.021 5.979,1.219 0.333,0.198 10 false BUZ 5.469,0.917 5.615,1.094 0.146,0.177 10 false 3 4.698,0.917 4.844,1.094 0.146,0.177 10 false 2 2.167,1.167 3.188,1.365 1.021,0.198 10 false ECU-IG No.1

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot main switch assembly (warning canceling switch assembly) is on.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR (REAR CROSS TRAFFIC ALERT BUZZER - BATTERY AND BLIND SPOT MONITOR SENSOR LH)
2.CHECK HARNESS AND CONNECTOR (REAR CROSS TRAFFIC ALERT BUZZER - BATTERY AND BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the P19 rear cross traffic alert buzzer (blind spot monitor buzzer) connector.


b.

Disconnect the S5 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P19-2 (BZN) - S5-3 (BUZ) Always Below 1 Ω
P19-2 (BZN) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
P19-1 (BZP) - Body ground Ignition switch ON 11 to 14 V
P19-1 (BZP) - Body ground Ignition switch off Below 1 V




OK

3.REPLACE BLIND SPOT MONITOR BUZZER (REAR CROSS TRAFFIC ALERT BUZZER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE BLIND SPOT MONITOR BUZZER (REAR CROSS TRAFFIC ALERT BUZZER)

NEXT

4.CHECK DTC
4.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (REAR CROSS TRAFFIC ALERT BUZZER [BLIND SPOT MONITOR BUZZER] IS DEFECTIVE)

NG