Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type)
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234451 REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type) J

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM(for Navigation Receiver Type)  Reverse Signal Circuit  


DESCRIPTION

The navigation receiver assembly receives a reverse signal from the park/neutral position switch assembly.

WIRING DIAGRAM

E280619E22
5.24,1.802 6.531,2.188 1.292,0.385 10 false Navigation Receiver Assembly 5.229,1.615 5.844,1.813 0.615,0.198 10 false J135 3.271,1.49 3.885,1.688 0.615,0.198 10 false D35 3.271,1.667 4.656,2.073 1.385,0.406 10 false Park/Neutral Position Switch Assembly 5.427,0.958 6.042,1.156 0.615,0.198 10 false REV 4.104,0.958 4.323,1.156 0.219,0.198 10 false RL 3.448,0.958 3.667,1.156 0.219,0.198 10 false RB 3.25,0.854 3.396,1.052 0.146,0.198 10 false 2 4.417,0.844 4.563,1.042 0.146,0.198 10 false 1 5.208,0.854 5.354,1.052 0.146,0.198 10 false 2 2.063,1.146 2.635,1.333 0.573,0.188 10 false LH-IG*1 0.135,1.219 1.531,1.479 1.396,0.26 10 false from IG1 No.2 Relay*2 0.146,0.948 1.479,1.156 1.333,0.208 10 false from IG No.1 Relay*1 2.052,1.365 2.896,1.583 0.844,0.219 10 false BK/UP LP*2 0.177,2.135 1.813,2.354 1.635,0.219 10 false *1: for Column Shift Type 0.177,2.385 1.813,2.604 1.635,0.219 10 false *2: for Floor Shift Type

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E278094

Enter the "Function Check/Setting I" mode and select "Vehicle Signal" (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK).


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R ON
Except R OFF


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.




OK

NG

2.CHECK NAVIGATION RECEIVER ASSEMBLY
2.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
U152701E02
0.927,1.365 0.625,0.958 0.625,0.958 0.51,0.958 true 0.115,0.063 0.354,0.25 0.24,0.188 10 false *a 1.573,0.49 1.938,0.677 0.365,0.188 10 false J135 0.135,0.875 0.469,1.042 0.333,0.167 10 false REV

Disconnect the navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J135-2 (REV) - Body ground Ignition switch ON, shift lever in R 7.5 to 14 V
J135-2 (REV) - Body ground Ignition switch ON, shift lever not in R Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)

Result
Result Proceed to
OK (for Column Shift Type) A
OK (for Floor Shift Type) B
NG C



A

B

C

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the J135 navigation receiver assembly connector.


b.

Disconnect the D35 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J135-2 (REV) - D35-1 (RL) Always Below 1 Ω
J135-2 (REV) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
U152816E02
1.792,1.021 2.521,0.698 2.521,0.698 2.74,0.698 true 2.813,0.625 3.104,0.833 0.292,0.208 10 false RB 1.563,0.333 1.854,0.542 0.292,0.208 10 false D35 0.115,0.063 0.406,0.271 0.292,0.208 10 false *a

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D35-2 (RB) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)

HINT:

*: Replace park/neutral position switch assembly procedure





OK

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY*

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR