Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM(for Radio and Display Type)
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234452 REAR VIEW MONITOR SYSTEM(for Radio and Display Type) C

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM(for Radio and Display Type)  C1622  Open or Short Circuit in Back Camera Signal  


DESCRIPTION

This DTC is stored if the radio and display receiver assembly judges as a result of its self check that the signals or signal lines between the radio and display receiver assembly and the television camera assembly are not normal.

DTC Code DTC Detection Condition Trouble Area
C1622 Open or Short Circuit in television camera signal
·

Harness or connector

·

Television camera assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E224828E26
5.615,2.813 5.979,2.979 0.365,0.167 10 false J140 5.479,2.25 5.688,2.417 0.208,0.167 10 false 23 5.75,2.375 6.198,2.542 0.448,0.167 10 false CGND 2.417,2.563 2.604,2.719 0.188,0.156 10 false * 5.479,1.833 5.688,2 0.208,0.167 10 false 24 5.76,1.969 6.208,2.135 0.448,0.167 10 false V- 5.479,1.354 5.677,1.521 0.198,0.167 10 false 12 5.76,1.479 6.208,1.646 0.448,0.167 10 false V+ 5.479,0.885 5.688,1.052 0.208,0.167 10 false 11 5.74,1 6.188,1.167 0.448,0.167 10 false CA+ 1.542,2.26 1.75,2.427 0.208,0.167 10 false 5 1.031,2.375 1.479,2.542 0.448,0.167 10 false CGND 1.542,1.844 1.75,2.01 0.208,0.167 10 false 2 1.198,1.948 1.479,2.115 0.281,0.167 10 false CV- 1.542,1.344 1.698,1.51 0.156,0.167 10 false 3 1.167,1.469 1.479,1.635 0.313,0.167 10 false CV+ 1.542,0.885 1.698,1.052 0.156,0.167 10 false 6 1.167,0.99 1.479,1.156 0.313,0.167 10 false CB+ 5.604,2.979 6.896,3.375 1.292,0.396 10 false Radio and Display Receiver Assembly 0.219,2.792 0.583,2.958 0.365,0.167 10 false X1 0.219,2.969 1.438,3.344 1.219,0.375 10 false Television Camera Assembly 0.167,3.448 0.938,3.656 0.771,0.208 10 false *: Shielded 3.531,2.552 3.719,2.708 0.188,0.156 10 false * 4.677,2.542 4.865,2.698 0.188,0.156 10 false *

PROCEDURE

1.CHECK FOR DTC

A

B

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION CAMERA ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the J140 radio and display receiver assembly connector.


b.

Disconnect the X1 television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J140-11 (CA+) - X1-6 (CB+) Always Below 1 Ω
J140-12 (V+) - X1-3 (CV+) Always Below 1 Ω
J140-23 (CGND) - X1-5 (CGND) Always Below 1 Ω
J140-24 (V-) - X1-2 (CV-) Always Below 1 Ω
J140-11 (CA+) - Body ground Always 10 kΩ or higher
J140-12 (V+) - Body ground Always 10 kΩ or higher
J140-23 (CGND) - Body ground Always 10 kΩ or higher
J140-24 (V-) - Body ground Always 10 kΩ or higher




OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
U152844E02
0.948,1.271 0.698,1.521 0.698,1.521 0.49,1.521 true 1.083,1.271 0.938,1.896 0.938,1.896 0.813,1.896 true 1.583,0.292 2.031,0.458 0.448,0.167 10 false J140 0.375,1.823 0.865,2.021 0.49,0.198 10 false CGND 0.271,1.427 0.51,1.625 0.24,0.198 10 false V- 0.115,0.073 0.354,0.271 0.24,0.198 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J140-23 (CGND) - Body ground Always Below 1 Ω
J140-24 (V-) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Radio and Display Receiver Assembly)

Result
Result Proceed to
OK A
NG (for Column Shift Type) B
NG (for Floor Shift Type) C



A

4.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

B

C

4.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
U152815E02
1.865,1.521 2.5,1.656 2.5,1.656 2.708,1.656 true 1.677,1.521 1.198,1.646 1.198,1.646 0.844,1.646 true 0.146,0.083 0.542,0.271 0.396,0.188 10 false *a 1.615,0.26 1.833,0.448 0.219,0.188 10 false X1 2.771,1.573 3.208,1.76 0.438,0.188 10 false CB+ 0.406,1.573 0.844,1.76 0.438,0.188 10 false CGND

Disconnect the television camera assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
X1-6 (CB+) - X1-5 (CGND) Ignition switch ACC 5.5 to 7.05 V


Text in Illustration
*a Front view of wire harness connector
(to Television Camera Assembly)

Result
Result Proceed to
OK A
NG (for Column Shift Type) B
NG (for Floor Shift Type) C



A

5.CHECK TELEVISION CAMERA ASSEMBLY

B

C

5.CHECK TELEVISION CAMERA ASSEMBLY
a.

Using an oscilloscope, check the waveform.

U152820E02
0.594,1.333 0.51,0.792 0.51,0.792 0.344,0.792 true 0.583,1.51 0.5,2.063 0.5,2.063 0.333,2.063 true 2.792,1.896 2.708,2.448 2.708,2.448 2.552,2.448 true 2.906,1.802 2.99,2.448 2.99,2.448 3.146,2.448 true 5.427,1.74 5.354,2.427 5.354,2.427 5.198,2.427 true 5.552,1.677 5.635,2.417 5.635,2.417 5.792,2.417 true 0.135,0.719 0.375,0.885 0.24,0.167 10 false V+ 0.104,0.104 0.344,0.271 0.24,0.167 10 false *a 2.281,0.104 2.521,0.271 0.24,0.167 10 false *b 2.375,2.365 2.615,2.531 0.24,0.167 10 false *d 4.833,0.104 5.073,0.271 0.24,0.167 10 false *c 2.042,1.354 2.448,1.521 0.406,0.167 10 false GND 1,0.729 1.406,0.896 0.406,0.167 10 false J140 4.635,1.354 5.042,1.521 0.406,0.167 10 false GND 0.146,1.969 0.385,2.135 0.24,0.167 10 false V- 3.188,2.365 3.427,2.531 0.24,0.167 10 false *e 4.99,2.333 5.229,2.5 0.24,0.167 10 false *d 5.833,2.313 6.073,2.479 0.24,0.167 10 false *e

Text in Illustration
*a Component with harness connected
(Radio and Display Receiver Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronized Signal
*e Video Waveform - -

Measurement Condition
Item Content
Tester Connection J140-12 (V+) - J140-24 (V-)
Tool Setting 0.2 V/DIV., 50 μs/DIV.
Condition

Waveform 1: Ignition switch ON

Waveform 2: Ignition switch ON, screen blacked out by covering camera lens



OK:

Waveform is as shown in illustration.


HINT:

The video waveform changes according to the image sent by the television camera assembly.




OK

NG

6.REPLACE TELEVISION CAMERA ASSEMBLY
6.REPLACE TELEVISION CAMERA ASSEMBLY
a.

Replace the television camera assembly with a new or normally functioning one (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA>REMOVAL).



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR).

Result
Result Proceed to
No DTC is output A
DTC is output (for Column Shift Type) B
DTC is output (for Floor Shift Type) C



A

END (TELEVISION CAMERA ASSEMBLY WAS DEFECTIVE)

B

C