Use the same procedure for the LH side and RH side.
The procedure listed below is for the LH side.
1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
69284D
2.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH
for Double Cab:
Remove the rear door inside handle bezel plug LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>DISASSEMBLY).
for CrewMax:
Remove the rear door inside handle bezel plug LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>DISASSEMBLY).
74272A
3.REMOVE REAR UPPER DOOR ARMREST BASE PANEL LH
for Double Cab:
Remove the rear upper door armrest base panel LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>DISASSEMBLY).
for CrewMax:
Remove the rear upper door armrest base panel LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>DISASSEMBLY).
67674A
4.REMOVE REAR DOOR FRAME GARNISH LH
for Double Cab:
Remove the rear door frame garnish LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>DISASSEMBLY).
for CrewMax:
Remove the rear door frame garnish LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>DISASSEMBLY).
67604
5.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
for Double Cab:
Remove the rear door trim board sub-assembly LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>DISASSEMBLY).
for CrewMax:
Remove the rear door trim board sub-assembly LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>DISASSEMBLY).
67626C
6.REMOVE REAR NO. 2 DOOR TRIM BRACKET
for Double Cab:
Remove the rear No. 2 door trim bracket (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>DISASSEMBLY).
for CrewMax:
Remove the rear No. 2 door trim bracket (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>DISASSEMBLY).
67842E
7.REMOVE REAR DOOR SERVICE HOLE COVER LH
for Double Cab:
Remove the rear door service hole cover LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>DISASSEMBLY).
for CrewMax:
Remove the rear door service hole cover LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>DISASSEMBLY).
68152C
8.REMOVE REAR DOOR GLASS RUN LH
for Double Cab:
Remove the rear door glass run LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>DISASSEMBLY).
for CrewMax:
Remove the rear door glass run LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>DISASSEMBLY).
67408F
9.REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH
for Double Cab:
Remove the rear door rear lower window frame sub-assembly LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>DISASSEMBLY).
for CrewMax:
Remove the rear door rear lower window frame sub-assembly LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>DISASSEMBLY).
68104
10.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
for Double Cab:
Remove the rear door glass sub-assembly LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>DISASSEMBLY).
for CrewMax:
Remove the rear door glass sub-assembly LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>DISASSEMBLY).
69804
11.REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
for Double Cab:
Remove the rear door window regulator sub-assembly LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>DISASSEMBLY).
for CrewMax:
Remove the rear door window regulator sub-assembly LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>DISASSEMBLY).
85720A
12.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
for Double Cab:
Using a T25 "TORX" driver, remove the 3 screws and motor.
Be careful when removing the screws as the motor may fall and become damaged.
for CrewMax:
Using a T25 "TORX" driver, remove the 3 screws and motor.
| *1 | Spring | - | - |
| *a | Range of Movement | - | - |
Do not place your finger, etc. within the range of movement of the window regulator. When removing the power window regulator motor, the force of the spring causes the window regulator to move in the direction of the arrow shown in the illustration (the direction in which the window rises), which may cause injury.
Be careful when removing the screws as the motor may fall and become damaged.