When the air conditioning control assembly (rear window defogger switch) is turned on, a rear window defogger activation request signal is sent via the LIN communication line to the air conditioning amplifier. Then the air conditioning amplifier operates the rear window defogger.
This circuit uses the LIN communication line. Before performing the inspection, check that the LIN communication system is functioning normally (see page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
Select the Active Test, using the Techstream to generate a control command, and then check that the rear window defogger operates (see page Vehicle Interior>WINDOW / GLASS>WINDOW DEFOGGER SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Defogger Relay (Rear) | Defogger relay | ON or OFF | - |
Rear window defogger operates normally.
OK
NG
Temporarily replace the air conditioning control assembly with a new or normally functioning one (see page Vehicle Interior>AIR CONDITIONING>AIR CONDITIONING PANEL>REMOVAL).
Check that the malfunction disappears.
Malfunction disappears.
OK
NG
Remove the DEFOG H-fuse from the engine room relay block, junction block.
Remove the ECU-IG No.1 fuse from the driver side junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DEFOG H-fuse | Always | Below 1 Ω |
| ECU-IG No.1 fuse | Always | Below 1 Ω |
OK
NG
Remove the defogger relay (DEFOG) from the engine room relay block, junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 4 | When battery voltage is not applied between terminals 1 and 2 | Below 1 Ω |
| 3 - 5 | 10 kΩ or higher | |
| 3 - 4 | When battery voltage is applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω |
OK
NG
Remove the defogger relay (DEFOG) from the engine room relay block, junction block.
Disconnect the J19 air conditioning amplifier connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Defogger relay (DEFOG) terminal 2 - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch OFF | Below 1 V | |
| Defogger relay (DEFOG) terminal 5 - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Defogger relay (DEFOG) terminal 1 - J19-38 (RDEF) | Always | Below 1 Ω |
| Defogger relay (DEFOG) terminal 1 or J19-38 (RDEF) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the P9 and P10 rear window glass (defogger wire) connectors.
Remove the defogger relay (DEFOG) from the engine room relay block, junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P9-1 (B) - Defogger relay (DEFOG) terminal 3 | Always | Below 1 Ω |
| P10-1 (E) - Body ground | Always | Below 1 Ω |
| Defogger relay (DEFOG) terminal 4 - Body ground | Always | Below 1 Ω |
| P9-1 (B) or Defogger relay (DEFOG) terminal 3 - Body ground | Always | 10 kΩ or higher |
OK
NG
Perform the on-vehicle inspection, check that the window defogger system operates normally (see page Vehicle Interior>WINDOW / GLASS>WINDOW DEFOGGER WIRE(for CrewMax)>ON-VEHICLE INSPECTION).
Malfunction disappears.
OK
NG