Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234473 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  Rear Power Window RH does not Operate with Rear Power Window Switch RH  


DESCRIPTION

If the rear RH side manual UP/DOWN function does not operate, there may be a malfunction in the rear switch RH, the rear motor RH, the master switch, or the harness or connector.


WIRING DIAGRAM

B231419E04
0.309,0.262 1.501,0.481 1.193,0.219 10 from P/W Relay 0.468,1.545 1.339,1.895 0.871,0.350 10 from POWER No. 3 Fuse 1.681,1.019 1.858,1.182 0.177,0.163 10 13 1.951,1.137 2.077,1.286 0.127,0.150 10 B 1.951,1.566 2.077,1.715 0.127,0.150 10 B 1.734,1.453 1.833,1.616 0.099,0.163 10 3 1.761,2.007 1.870,2.170 0.108,0.163 10 1 1.951,2.152 2.082,2.315 0.131,0.163 10 E 2.546,0.959 2.687,1.113 0.141,0.154 10 U 2.762,0.834 2.953,0.997 0.191,0.163 10 10 2.551,1.776 2.687,1.921 0.136,0.145 10 D 2.772,1.674 2.972,1.819 0.200,0.145 10 16 1.42,2.695 3.029,3.028 1.609,0.333 10 Power Window Regulator Master Switch Assembly 3.616,0.179 3.726,0.340 0.111,0.160 10 3 3.821,0.282 3.948,0.437 0.127,0.155 10 B 3.613,0.824 3.729,0.995 0.116,0.171 10 5 3.815,0.952 4.053,1.106 0.237,0.155 10 SU 3.606,1.691 3.715,1.843 0.110,0.152 10 2 3.824,1.783 4.039,1.954 0.215,0.171 10 SD 4.423,0.975 4.564,1.129 0.141,0.154 10 U 4.428,1.792 4.564,1.937 0.136,0.145 10 D 4.678,0.845 4.797,1.017 0.118,0.172 10 4 4.708,1.691 4.824,1.845 0.116,0.154 10 1 5.602,0.874 5.712,1.026 0.110,0.152 10 2 5.605,1.685 5.721,1.839 0.116,0.154 10 1 3.565,2.693 4.873,3.203 1.309,0.510 10 Rear Power Window Regulator Switch Assembly RH 5.698,2.411 6.997,2.938 1.299,0.527 10 Rear Power Window Regulator Motor Assembly RH 1.42,2.52 1.666,2.662 0.246,0.142 10 N2 3.565,2.531 3.936,2.707 0.372,0.176 10 O5 5.698,2.243 6.048,2.400 0.351,0.158 10 O3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (REAR SWITCH RH - BATTERY)
a.
U151871E02
1.656,1.969 1.99,2.333 false 0.24,0.125 2.521,0.5 2.281,0.375 10 false Front view of wire harness connector: (to Rear Switch RH) 0.771,1.76 1.01,1.917 0.24,0.156 10 false O5 2.052,2.302 2.198,2.469 0.146,0.167 10 false B

Disconnect the O5 switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O5-3 (B) - Body ground Ignition switch ON 11 to 14 V




OK

2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
a.
B166135E13
1.302,2.771 0.938,2.833 false 1.531,2.813 1.135,3.073 false 1.76,2.823 1.698,3.094 false 2,2.781 2.354,3.073 false 2.198,2.76 2.698,2.792 false 0.115,1.292 2.583,1.656 2.469,0.365 10 false Component without harness connected: (Rear Switch RH) 0.677,2.792 1,2.969 0.323,0.177 10 false SU 1,3.052 1.198,3.229 0.198,0.177 10 false U 1.604,3.083 1.781,3.26 0.177,0.177 10 false B 2.365,3.052 2.625,3.229 0.26,0.177 10 false SD 2.74,2.74 2.917,2.917 0.177,0.177 10 false D

Remove the rear switch RH (See page Vehicle Interior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (U) - 3 (B) UP Below 1 Ω
1 (D) - 2 (SD) UP Below 1 Ω
4 (U) - 5 (SU) OFF Below 1 Ω
1 (D) - 2 (SD) OFF Below 1 Ω
4 (U) - 5 (SU) DOWN Below 1 Ω
1 (D) - 3 (B) DOWN Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (REAR SWITCH RH - REAR MOTOR RH)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

3.CHECK HARNESS AND CONNECTOR (REAR SWITCH RH - REAR MOTOR RH)
a.
U151997E02
0.906,2.135 1.375,2.01 false 1.885,2.021 2.521,2.156 false 0.188,0.229 2.573,0.74 2.385,0.51 10 false Front view of wire harness connector: (to Rear Switch RH) 2.594,2.083 2.729,2.25 0.135,0.167 10 false U 0.771,2.083 0.896,2.24 0.125,0.156 10 false D 0.125,2.594 2.479,3.115 2.354,0.521 10 false Front view of wire harness connector: (to Rear Motor RH) 0.375,1.635 0.656,1.802 0.281,0.167 10 false O5 0.438,3.844 0.719,4.01 0.281,0.167 10 false O3

Disconnect the O5 switch connector.


b.

Disconnect the O3 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O5-1 (D) - O3-1 Always Below 1 Ω
O5-4 (U) - O3-2 Always Below 1 Ω
O5-1 (D) - Body ground Always 10 kΩ or higher
O5-4 (U) - Body ground Always 10 kΩ or higher




OK

4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.
B231476E01
1.871,1.826 2.21,0.978 2.21,0.978 2.378,0.978 false 2.404,0.905 3.143,1.058 0.739,0.152 10 Motor Gear 0.308,1.899 0.988,2.044 0.680,0.145 10 Clockwise 0.521,2.813 1.642,2.958 1.121,0.145 10 Counterclockwise 0.074,0.054 2.598,0.478 2.524,0.423 10 Component without harness connected: (Rear Motor RH)

Remove the rear motor RH (See page Vehicle Interior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Rear Door)>REMOVAL).


b.

Apply battery voltage to connector terminals 1 and 2.


c.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates clockwise
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates counterclockwise




OK

5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - REAR SWITCH RH)

NG

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - REAR SWITCH RH)
a.
U151999E01
0.083,0.179 2.509,0.668 2.426,0.489 10 Front view of wire harness connector: (to Master Switch) 0.117,2.845 2.544,3.334 2.426,0.489 10 Front view of wire harness connector: (to Rear Switch RH) 0.391,2.169 0.527,2.332 0.136,0.164 10 U 2.909,2.304 3.072,2.468 0.163,0.164 10 D 0.585,2.238 0.967,2.106 false 2.09,2.106 2.841,2.386 false 2.59,4.285 2.834,4.449 0.244,0.164 10 SU 0.575,4.279 0.815,4.442 0.240,0.164 10 SD 0.851,4.373 1.546,4.348 false 2.012,4.353 2.538,4.382 false 0.235,1.628 0.475,1.779 0.240,0.150 10 N2 0.327,3.917 0.637,4.068 0.310,0.150 10 O5

Disconnect the N2 master switch connector.


b.

Disconnect the O5 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-10 (U) - O5-5 (SU) Always Below 1 Ω
N2-16 (D) - O5-2 (SD) Always Below 1 Ω
N2-10 (U) - Body ground Always 10 kΩ or higher
N2-16 (D) - Body ground Always 10 kΩ or higher




OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR