Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234473 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch  


DESCRIPTION

If the manual UP/DOWN function does not operate, there may be a malfunction in the power window regulator switch assembly, the front passenger side motor, or the harness or connector.


WIRING DIAGRAM

B233012E01
0.673,0.755 3.966,0.935 3.293,0.180 10 from Main Body ECU (Driver Side Junction Block) 5.489,2.67 6.038,2.840 0.549,0.170 10 DOWN 3.665,2.67 4.127,2.840 0.461,0.170 10 DOWN 4.253,2.587 4.447,2.743 0.194,0.156 10 7 5.223,2.583 5.355,2.736 0.132,0.152 10 7 5.489,2.229 5.770,2.399 0.281,0.170 10 UP 5.489,1.105 5.646,1.275 0.156,0.170 10 B 5.489,1.518 5.867,1.688 0.378,0.170 10 GND 0.668,4.269 2.637,4.438 1.969,0.170 10 : LIN Communication Line 3.185,3.276 3.528,3.446 0.343,0.170 10 GND 3.919,2.23 4.141,2.399 0.222,0.170 10 UP 4.253,2.138 4.461,2.291 0.208,0.152 10 6 5.263,1.011 5.384,1.163 0.121,0.152 10 2 5.263,1.408 5.384,1.560 0.121,0.152 10 1 5.183,2.123 5.391,2.275 0.208,0.152 10 10 2.69,3.744 4.727,4.112 2.037,0.368 10 Power Window Regulator Switch Assembly 5.061,3.728 7.013,4.070 1.952,0.342 10 Front Power Window Regulator Motor Assembly RH 2.955,3.199 3.064,3.355 0.109,0.156 10 1 2.692,3.572 3.003,3.728 0.311,0.156 10 M10 5.061,3.548 5.390,3.704 0.329,0.156 10 M11 0.868,1.086 1.655,1.401 0.787,0.316 10 from Battery 1.776,1.251 2.777,1.410 1.002,0.158 10 POWER NO. 4 5.253,0.647 5.363,0.815 0.110,0.168 10 9 5.489,0.795 5.747,0.942 0.257,0.147 10 LIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK LIN COMMUNICATION SYSTEM
a.

Check for LIN communication system DTCs related to the power window control system (See page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

OK:

LIN communication system DTCs are not output.




OK

2.CHECK FOR DTC (B2312)

NG

2.CHECK FOR DTC (B2312)
a.

Check if DTC B2312 is output (See page Vehicle Interior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR).

OK:

DTC B2312 is not output.




OK

3.READ VALUE USING TECHSTREAM (FRONT PASSENGER SIDE MOTOR)

NG

3.READ VALUE USING TECHSTREAM (FRONT PASSENGER SIDE MOTOR)
a.

Use the Data List to check if the front passenger side motor is functioning properly.

P-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P Door P/W Up SW Front passenger side power window manual UP switch signal / ON or OFF ON: Power window regulator switch assembly operated
OFF: Power window regulator switch assembly not operated
-
P Door P/W Down SW Front passenger side power window manual DOWN switch signal / ON or OFF ON: Power window regulator switch assembly operated
OFF: Power window regulator switch assembly not operated
-

OK:

The Techstream display changes normally when power window regulator switch assembly is operated.




OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - BODY GROUND)
a.
U151991E01
0.17,0.134 2.610,0.873 2.441,0.739 10 Front view of wire harness connector: (to Power Window Regulator Switch Assembly) 0.795,1.704 1.099,1.863 0.304,0.159 10 M10 0.819,2.471 1.153,2.623 0.333,0.152 10 GND 1.149,2.471 1.491,2.151 false

Disconnect the M10 switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M10-1 (GND) - Body ground Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (FRONT PASSENGER SIDE MOTOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (FRONT PASSENGER SIDE MOTOR - BATTERY AND BODY GROUND)
a.
U151990E01
0.165,0.13 2.625,0.627 2.460,0.496 10 Front view of wire harness connector: (to Front Passenger Side Motor) 0.674,1.229 1.007,1.385 0.333,0.156 10 M11 2.438,2.053 2.610,2.242 0.172,0.189 10 B 0.76,2.046 1.111,2.235 0.350,0.189 10 GND 1.568,1.745 1.009,2.046 false 1.895,1.757 2.454,2.058 false

Disconnect the M11 motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M11-2 (B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
M11-1 (GND) - Body ground Always Below 1 Ω




OK

6.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT PASSENGER SIDE MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT PASSENGER SIDE MOTOR)
a.
U151993E02
1.115,1.677 1.594,1.771 false 1.854,1.76 2.375,1.458 false 1.906,4.031 2.271,3.854 false 1.146,4.156 1.5,3.99 false 0.406,2.198 2.677,2.594 2.271,0.396 10 false Front view of wire harness connector: (to Front Passenger Side Motor) 0.281,0.031 2.563,0.583 2.281,0.552 10 false Front view of wire harness connector: (to Power Window Regulator Switch Assembly) 0.615,1.229 0.906,1.406 0.292,0.177 10 false M10 0.604,3.25 0.906,3.427 0.302,0.177 10 false M11 0.896,1.615 1.177,1.781 0.281,0.167 10 false UP 2.375,1.385 2.854,1.573 0.479,0.188 10 false DOWN 2.302,3.729 2.583,3.896 0.281,0.167 10 false UP 0.573,4.115 1.052,4.302 0.479,0.188 10 false DOWN

Disconnect the M10 switch connector.


b.

Disconnect the M11 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M10-6 (UP) - M11-10 (UP) Always Below 1 Ω
M10-7 (DOWN) - M11-7 (DOWN) Always Below 1 Ω
M10-6 (UP) - Body ground Always 10 kΩ or higher
M10-7 (DOWN) - Body ground Always 10 kΩ or higher




OK

7.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
a.
B231347E04
0.035,1.236 2.806,1.591 2.772,0.355 10 Component without harness connected: (Power Window Regulator Switch Assembly) 1.398,3.17 1.862,3.309 0.464,0.140 10 DOWN 2.455,2.445 2.784,2.598 0.330,0.154 10 GND 2.166,3.161 2.393,3.308 0.228,0.147 10 UP 1.674,2.801 1.674,3.154 false 1.86,2.812 2.274,3.154 false 2.097,2.542 2.438,2.542 false

Remove the power window regulator switch assembly (See page Vehicle Interior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (UP) - 1 (GND) Manual UP operation Below 1 Ω
7 (DOWN) - 1 (GND) Manual DOWN operation Below 1 Ω
6 (UP) - 1 (GND) Not operated 10 kΩ or higher
7 (DOWN) - 1 (GND) Not operated 10 kΩ or higher




OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY