Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234473 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  B2312  Power Window Switch Malfunction  


DESCRIPTION

The power window regulator sub-assembly consists of the motor, regulator and ECU. The power window regulator motor is driven by operating the power window switch. This DTC is output when the ECU built into the regulator motor determines that the power window switch is stuck.

NOTICE:
·

When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized.

·

After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the AUTO UP function is used. In such cases, the AUTO UP function can be resumed by repeating the following operation at least 5 times:

(a) Close the power window by fully pulling up the power window switch and holding it in the AUTO UP position.

(b) Open the power window by fully pushing down the power window switch.



Master Switch
DTC Code DTC Detection Condition Trouble Area
B2312
·

The power window regulator master switch is stuck.

·

The power window regulator master switch is held in the same position for more than 20 seconds.


·

Power window regulator master switch assembly

·

Harness or connector

·

Power window regulator master switch assembly held in same position for more than 20 seconds



Driver Side Motor
DTC Code DTC Detection Condition Trouble Area
B2312
·

The power window regulator master switch stuck.

·

The power window regulator master switch is held in the same position for more than 20 seconds.


·

Power window regulator master switch assembly

·

Front power window regulator motor assembly LH

·

Harness or connector

·

Power window regulator master switch assembly held in same position for more than 20 seconds



Front Passenger Side Motor
DTC Code DTC Detection Condition Trouble Area
B2312
·

The power window regulator switch is stuck.

·

The power window regulator switch is held in the same position for more than 20 seconds.


·

Power window regulator switch assembly

·

Front power window regulator motor assembly RH

·

Harness or connector

·

Power window regulator switch assembly held in same position for more than 20 seconds



WIRING DIAGRAM

B178355E05
0.313,0.031 1.49,0.25 1.177,0.219 12 false for Driver Side: 0.229,0.677 1.969,1.063 1.74,0.385 10 false from Main Body ECU (Driver Side Junction Block) 2.094,5.052 3.844,5.458 1.75,0.406 10 false from Main Body ECU (Driver Side Junction Block) 3.042,0.604 3.167,0.76 0.125,0.156 10 false 6 4.333,0.604 4.458,0.76 0.125,0.156 10 false 7 3.229,0.75 3.542,0.906 0.313,0.156 10 false LIN1 3.906,0.75 4.24,0.906 0.333,0.156 10 false LIN2 3.042,1.323 3.167,1.5 0.125,0.177 10 false 1 3.271,1.458 3.417,1.604 0.146,0.146 10 false E 3.938,1.073 4.177,1.229 0.24,0.156 10 false UP 3.729,1.531 4.198,1.688 0.469,0.156 10 false DOWN 4.333,0.979 4.438,1.135 0.104,0.156 10 false 4 4.333,1.427 4.438,1.573 0.104,0.146 10 false 5 2.896,2.167 4.521,2.51 1.625,0.344 10 false Power Window Regulator Master Switch Assembly 5.365,0.604 5.469,0.771 0.104,0.167 10 false 9 5.542,0.74 5.781,0.896 0.24,0.156 10 false LIN 5.281,0.979 5.469,1.156 0.188,0.177 10 false 10 5.563,1.083 5.802,1.24 0.24,0.156 10 false UP 5.563,1.552 6.031,1.708 0.469,0.156 10 false DOWN 5.365,1.427 5.469,1.583 0.104,0.156 10 false 7 5.333,3.104 5.448,3.26 0.115,0.156 10 false 1 5.573,3.229 5.917,3.385 0.344,0.156 10 false GND 4.979,3.979 6.969,4.323 1.99,0.344 10 false Front Power Window Regulator Motor Assembly LH 0.771,8.594 2.396,8.771 1.625,0.177 10 false : LIN Communication Line 2.906,2.01 3.135,2.188 0.229,0.177 10 false N2 4.979,3.792 5.313,3.958 0.333,0.167 10 false N12 0.281,4.646 2.604,4.865 2.323,0.219 12 false for Front Passenger Side: 4.365,6.448 4.49,6.604 0.125,0.156 10 false 6 4.354,6.875 4.479,7.031 0.125,0.156 10 false 7 3.063,7.458 3.188,7.635 0.125,0.177 10 false 1 3.292,7.594 3.646,7.74 0.354,0.146 10 false GND 3.99,6.573 4.229,6.729 0.24,0.156 10 false UP 3.74,6.99 4.208,7.146 0.469,0.156 10 false DOWN 5.375,7.354 5.479,7.51 0.104,0.156 10 false 4 4.354,7.354 4.458,7.5 0.104,0.146 10 false 8 2.667,7.927 4.677,8.271 2.01,0.344 10 false Power Window Regulator Switch Assembly 5.385,4.99 5.49,5.156 0.104,0.167 10 false 9 5.563,5.125 5.802,5.281 0.24,0.156 10 false LIN 5.302,6.427 5.49,6.604 0.188,0.177 10 false 10 5.583,6.542 5.823,6.698 0.24,0.156 10 false UP 5.583,7.021 6.052,7.177 0.469,0.156 10 false DOWN 5.385,6.896 5.49,7.052 0.104,0.156 10 false 7 5.354,5.708 5.469,5.865 0.115,0.156 10 false 1 5.594,5.833 5.938,5.99 0.344,0.156 10 false GND 5,7.927 6.99,8.271 1.99,0.344 10 false Front Power Window Regulator Motor Assembly RH 2.677,7.771 3.021,7.948 0.344,0.177 10 false M10 5,7.74 5.323,7.906 0.323,0.167 10 false M11 5.594,7.469 6,7.625 0.406,0.156 10 false AUTO 3.823,7.448 4.229,7.604 0.406,0.156 10 false AUTO

PROCEDURE

1.CHECK LIN COMMUNICATION SYSTEM
a.

Check for LIN communication system DTCs related to the power window control system (See page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

OK:

LIN communication system DTCs are not output.




OK

2.CHECK DTC

NG

2.CHECK DTC
a.

Check where DTC B2312 is output from.

Result
Result Proceed to
DTC B2312 output from power window regulator master switch assembly. A
DTC B2312 output from front power window regulator motor assembly LH. B
DTC B2312 output from front power window regulator motor assembly RH. C



A

3.READ VALUE USING TECHSTREAM (MASTER SWITCH)

B

4.READ VALUE USING TECHSTREAM (DRIVER SIDE MOTOR)

C

6.READ VALUE USING TECHSTREAM (FRONT PASSENGER SIDE MOTOR)
3.READ VALUE USING TECHSTREAM (MASTER SWITCH)
a.

Use the Data List to check if the master switch is functioning properly.

Master Switch
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver side power window auto UP/DOWN switch signal / ON or OFF ON: Driver side switch of master switch operated
OFF: Driver side switch of master switch not operated
-
P Door P/W Auto SW Front passenger side power window remote auto UP/DOWN switch signal / ON or OFF ON: Front passenger side switch of master switch operated
OFF: Front passenger side switch of master switch not operated
-
P Door P/W Up SW Front passenger side power window remote manual UP switch signal / ON or OFF ON: Front passenger side switch of master switch operated
OFF: Front passenger side switch of master switch not operated
-
P Door P/W Down SW Front passenger side power window remote manual DOWN switch signal / ON or OFF ON: Front passenger side switch of master switch operated
OFF: Front passenger side switch of master switch not operated
-
Window Lock Switch Status Power window LOCK switch / ON or OFF ON: Power window lock switch in LOCK position
OFF: Power window lock switch in UNLOCK position
-

OK:

The Techstream display changes normally when master switch is operated.




OK

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

4.READ VALUE USING TECHSTREAM (DRIVER SIDE MOTOR)
a.

Use the Data List to check if the driver side motor is functioning properly.

D-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver side power window auto UP/DOWN switch signal / ON or OFF ON: Driver side switch operated
OFF: Driver side switch not operated
-
D Door P/W Up SW Driver side power window MANUAL UP switch signal / ON or OFF ON: Driver side switch operated
OFF: Driver side switch not operated
-
D Door P/W Down SW Driver side power window MANUAL DOWN switch signal / ON or OFF ON: Driver side switch operated
OFF: Driver side switch not operated
-

OK:

The Techstream display changes normally when master switch is operated.




OK

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE)

NG

5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER SIDE MOTOR)
5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER SIDE MOTOR)
a.
U151995E01
0.29,0.185 2.646,0.693 2.356,0.508 10 Front view of wire harness connector: (to Master Switch) 0.205,2.499 2.562,3.007 2.356,0.508 10 Front view of wire harness connector: (to Driver Side Motor) 0.547,1.942 0.779,2.082 0.232,0.139 10 UP 2.713,2.018 3.172,2.170 0.459,0.152 10 DOWN 1.569,1.788 0.847,2.017 false 1.77,1.805 2.661,2.091 false 2.461,4.3 2.693,4.439 0.232,0.139 10 UP 0.584,4.387 1.043,4.539 0.459,0.152 10 DOWN 1.55,4.268 1.153,4.459 false 1.908,4.276 2.426,4.373 false 0.457,1.382 0.679,1.530 0.223,0.147 10 N2 0.696,3.7 1.060,3.847 0.364,0.147 10 N12

Disconnect the N2 master switch connector.


b.

Disconnect the N12 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-4 (UP) - N12-10 (UP) Always Below 1 Ω
N2-5 (DOWN) - N12-7 (DOWN) Always Below 1 Ω
N2-4 (UP) - Body ground Always 10 kΩ or higher
N2-5 (DOWN) - Body ground Always 10 kΩ or higher




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING TECHSTREAM (FRONT PASSENGER SIDE MOTOR)
a.

Use the Data List to check if the front passenger side motor is functioning properly.

P-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger side power window auto UP/DOWN switch signal / ON or OFF ON: Power window regulator switch assembly operated
OFF: Power window regulator switch assembly not operated
-
P Door P/W Up SW Front passenger side power window manual UP switch signal / ON or OFF ON: Power window regulator switch assembly operated
OFF: Power window regulator switch assembly not operated
-
P Door P/W Down SW Front passenger side power window manual DOWN switch signal / ON or OFF ON: Power window regulator switch assembly operated
OFF: Power window regulator switch assembly not operated
-

OK:

The Techstream display changes normally when master switch is operated.




OK

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE)

NG

7.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
7.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
a.
B231347E02
0.035,1.225 2.806,1.579 2.772,0.355 10 Component without harness connected: (Power Window Regulator Switch Assembly) 1.398,3.158 1.862,3.298 0.464,0.140 10 DOWN 0.794,3.158 1.199,3.307 0.406,0.149 10 AUTO 2.455,2.433 2.784,2.587 0.330,0.154 10 GND 2.166,3.15 2.393,3.296 0.228,0.147 10 UP 1.674,2.789 1.674,3.143 false 1.86,2.8 2.274,3.143 false 1.476,2.8 1.046,3.143 false 2.097,2.53 2.438,2.53 false

Remove the power window regulator switch assembly (See page Vehicle Interior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (UP) - 1 (GND) Manual UP operation Below 1 Ω
7 (DOWN) - 1 (GND) Manual DOWN operation Below 1 Ω
8 (AUTO) - 1 (GND) AUTO UP/DOWN operation Below 1 Ω
6 (UP) - 1 (GND) Not operated 10 kΩ or higher
7 (DOWN) - 1 (GND) Not operated 10 kΩ or higher
8 (AUTO) - 1 (GND) Not operated 10 kΩ or higher




OK

8.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT PASSENGER SIDE MOTOR)

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT PASSENGER SIDE MOTOR)
a.
U151992E02
1.188,1.635 1.635,1.813 true 1.823,1.74 2.302,1.354 true 1.958,1.75 2.375,1.573 true 1.24,3.646 1.594,3.854 false 1.896,4 2.26,3.823 false 1.219,4.229 1.5,3.99 false 0.438,2.219 2.708,2.594 2.271,0.375 10 false Front view of wire harness connector: (to Front Passenger Side Motor) 0.417,0.052 2.698,0.604 2.281,0.552 10 false Front view of wire harness connector: (to Power Window Regulator Switch Assembly) 0.604,1.229 0.927,1.417 0.323,0.188 10 false M10 0.615,3.26 0.927,3.438 0.313,0.177 10 false M11 0.938,1.531 1.219,1.698 0.281,0.167 10 false UP 2.354,1.271 2.833,1.458 0.479,0.188 10 false DOWN 2.406,1.49 2.823,1.656 0.417,0.167 10 false AUTO 2.302,3.729 2.583,3.896 0.281,0.167 10 false UP 0.635,4.177 1.115,4.365 0.479,0.188 10 false DOWN 0.781,3.531 1.198,3.698 0.417,0.167 10 false AUTO

Disconnect the M10 switch connector.


b.

Disconnect the M11 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M10-6 (UP) - M11-10 (UP) Always Below 1 Ω
M10-7 (DOWN) - M11-7 (DOWN) Always Below 1 Ω
M10-8 (AUTO) - M11-4 (AUTO) Always Below 1 Ω
M10-6 (UP) - Body ground Always 10 kΩ or higher
M10-7 (DOWN) - Body ground Always 10 kΩ or higher
M10-8 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR