Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234473 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  Rear Power Window LH does not Operate with Rear Power Window Switch LH  


DESCRIPTION

If the rear LH side manual UP/DOWN function does not operate, there may be a malfunction in the rear switch LH, the rear motor LH, the master switch, or the harness or connector.


WIRING DIAGRAM

B231419E03
0.309,0.262 1.501,0.481 1.193,0.219 10 from P/W Relay 0.455,1.545 1.333,1.895 0.878,0.350 10 from POWER No. 3 Fuse 1.681,1.019 1.858,1.182 0.177,0.163 10 13 1.951,1.137 2.077,1.286 0.127,0.150 10 B 1.951,1.566 2.077,1.715 0.127,0.150 10 B 1.734,1.453 1.833,1.616 0.099,0.163 10 3 1.761,2.007 1.870,2.170 0.108,0.163 10 1 1.951,2.152 2.082,2.315 0.131,0.163 10 E 2.546,0.959 2.687,1.113 0.141,0.154 10 U 2.762,0.834 2.953,0.997 0.191,0.163 10 12 2.551,1.776 2.687,1.921 0.136,0.145 10 D 2.772,1.674 2.972,1.819 0.200,0.145 10 15 1.42,2.695 3.029,3.028 1.609,0.333 10 Power Window Regulator Master Switch Assembly 3.616,0.179 3.726,0.340 0.111,0.160 10 3 3.821,0.282 3.948,0.437 0.127,0.155 10 B 3.613,0.824 3.729,0.995 0.116,0.171 10 5 3.815,0.952 4.053,1.106 0.237,0.155 10 SU 3.606,1.691 3.715,1.843 0.110,0.152 10 2 3.824,1.783 4.039,1.954 0.215,0.171 10 SD 4.423,0.975 4.564,1.129 0.141,0.154 10 U 4.428,1.792 4.564,1.937 0.136,0.145 10 D 4.678,0.845 4.797,1.017 0.118,0.172 10 4 4.708,1.691 4.824,1.845 0.116,0.154 10 1 5.602,0.874 5.712,1.026 0.110,0.152 10 2 5.605,1.685 5.721,1.839 0.116,0.154 10 1 3.565,2.693 4.873,3.203 1.309,0.510 10 Rear Power Window Regulator Switch Assembly LH 5.698,2.411 6.997,2.938 1.299,0.527 10 Rear Power Window Regulator Motor Assembly LH 1.42,2.52 1.666,2.662 0.246,0.142 10 N2 3.565,2.531 3.936,2.707 0.372,0.176 10 O11 5.698,2.243 6.048,2.400 0.351,0.158 10 O9

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (REAR SWITCH LH - BATTERY)
a.
U151870E02
1.667,1.958 2.021,2.313 false 0.188,0.448 2.458,0.833 2.271,0.385 10 false Front view of wire harness connector: (to Rear Switch LH) 0.729,1.76 1.021,1.906 0.292,0.146 10 false O11 2.125,2.281 2.271,2.448 0.146,0.167 10 false B

Disconnect the O11 switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O11-3 (B) - Body ground Ignition switch ON 11 to 14 V




OK

2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
a.
B166135E02
0.117,1.291 2.585,1.656 2.468,0.364 10 Component without harness connected: (Rear Switch LH) 0.674,2.79 1.001,2.969 0.327,0.179 10 SU 0.999,3.047 1.194,3.226 0.195,0.179 10 U 1.603,3.083 1.781,3.262 0.177,0.179 10 B 2.364,3.047 2.623,3.226 0.259,0.179 10 SD 2.735,2.743 2.912,2.922 0.177,0.179 10 D 1.328,2.696 0.934,2.835 false 1.54,2.749 1.14,3.068 false 1.764,2.754 1.686,3.089 false 1.938,2.765 2.353,3.074 false 2.183,2.696 2.702,2.793 false

Remove the rear switch LH (See page Vehicle Interior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (U) - 3 (B) UP Below 1 Ω
1 (D) - 2 (SD) UP Below 1 Ω
4 (U) - 5 (SU) OFF Below 1 Ω
1 (D) - 2 (SD) OFF Below 1 Ω
4 (U) - 5 (SU) DOWN Below 1 Ω
1 (D) - 3 (B) DOWN Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (REAR SWITCH LH - REAR MOTOR LH)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

3.CHECK HARNESS AND CONNECTOR (REAR SWITCH LH - REAR MOTOR LH)
a.
U151996E02
0.906,2.146 1.375,2.021 false 1.875,2 2.51,2.135 false 0.188,0.229 2.573,0.74 2.385,0.51 10 false Front view of wire harness connector: (to Rear Switch LH) 2.583,2.073 2.719,2.24 0.135,0.167 10 false U 0.729,2.073 0.854,2.229 0.125,0.156 10 false D 0.125,2.594 2.479,3.115 2.354,0.521 10 false Front view of wire harness connector: (to Rear Motor LH) 0.344,1.646 0.625,1.813 0.281,0.167 10 false O11 0.438,3.844 0.667,4 0.229,0.156 10 false O9

Disconnect the O11 switch connector.


b.

Disconnect the O9 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-1 (D) - O9-1 Always Below 1 Ω
O11-4 (U) - O9-2 Always Below 1 Ω
O11-1 (D) - Body ground Always 10 kΩ or higher
O11-4 (U) - Body ground Always 10 kΩ or higher




OK

4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
B231474E01
1.349,1.988 0.691,0.955 0.691,0.955 0.858,0.955 false 0.884,0.882 1.623,1.034 0.739,0.152 10 Motor Gear 1.909,2.952 2.589,3.098 0.680,0.145 10 Clockwise 1.952,1.993 3.073,2.138 1.121,0.145 10 Counterclockwise 0.046,0.05 2.707,0.494 2.661,0.445 10 Component without harness connected: (Rear Motor LH)


b.

Apply battery voltage to connector terminals 1 and 2.


c.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates counterclockwise
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates clockwise




OK

5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - REAR SWITCH LH)

NG

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

5.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - REAR SWITCH LH)
a.
U151998E01
0.083,0.179 2.509,0.668 2.426,0.489 10 Front view of wire harness connector: (to Master Switch) 0.117,2.845 2.544,3.334 2.426,0.489 10 Front view of wire harness connector: (to Rear Switch LH) 0.46,2.105 0.596,2.269 0.136,0.164 10 U 2.926,2.081 3.089,2.245 0.163,0.164 10 D 0.654,2.175 1.35,2.15 false 1.882,2.148 2.858,2.163 false 2.59,4.285 2.834,4.449 0.244,0.164 10 SU 0.575,4.279 0.815,4.442 0.240,0.164 10 SD 0.851,4.373 1.546,4.348 false 2.012,4.353 2.538,4.382 false 0.235,1.628 0.475,1.779 0.240,0.150 10 N2 0.304,3.917 0.614,4.068 0.310,0.150 10 O11

Disconnect the N2 master switch connector.


b.

Disconnect the O11 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-12 (U) - O11-5 (SU) Always Below 1 Ω
N2-15 (D) - O11-2 (SD) Always Below 1 Ω
N2-12 (U) - Body ground Always 10 kΩ or higher
N2-15 (D) - Body ground Always 10 kΩ or higher




OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR