Home › Vehicle Interior › INTERIOR › ROOF HEADLINING(for Regular Cab)
RM27M0U _58 Vehicle Interior _049165 INTERIOR _0234503 ROOF HEADLINING(for Regular Cab) A

INTERIOR  ROOF HEADLINING(for Regular Cab)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 63310 1.INSTALL ROOF HEADLINING ASSEMBLY

B356935

a.

Place the roof headlining assembly into the cabin as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining assembly when placing it in the cabin.



b.

Attach the 3 clips to install the roof headlining assembly.


c.

Attach the 4 wire harness clamps and connect the connector to the front pillar LH.


d.

w/ EC Mirror:

Connect the connector.


Hide 74631C 2.INSTALL COAT HOOK

a.

Using a T20 "TORX" driver, install the coat hook with the "TORX" screw.


b.

Attach the 2 claws to install the coat hook cap.


Hide 74310 5.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 87834 6.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 63650A 7.INSTALL ROOF CONSOLE BOX ASSEMBLY

Hide 62520P 8.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

a.

Attach the 5 clips to install the front quarter trim panel assembly LH.


b.

Install the 2 bolts.


c.

Connect the front seat outer belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


d.

Attach the 2 claws to close the shoulder belt anchor cover.

B355509


e.
B355506

Attach the claw to close the cover.


Hide 62510P 9.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62540 10.INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY LH

a.

Attach the 7 clips to install the lower quarter trim panel assembly LH.


b.
B166849

Twist the front seat outer belt assembly LH clockwise and connect it with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

Attach the 2 claws to install the cover.


Hide 62530 11.INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY RH

a.

Attach the 9 clips to install the lower quarter trim panel assembly RH.


b.

Install the jack assembly.


c.

Install the trim cover.


d.
B167430

Twist the front seat outer belt assembly RH counterclockwise and connect it with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


e.

Attach the 2 claws to install the cover.


Hide 64429E 14.INSTALL LUGGAGE COMPARTMENT BOX RH

a.

Install the luggage compartment box RH with the 4 clips.


Hide 64439D 15.INSTALL LUGGAGE COMPARTMENT BOX LH

a.

Attach the 3 claws to install the luggage compartment box LH.


b.

Install the 2 clips.


Hide 64261C 16.INSTALL UPPER BACK PANEL GARNISH

a.

Attach the 10 clips to install the upper back panel garnish.


Hide 62312B 17.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Install the front door opening trim weatherstrip LH.


Hide 62311B 18.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 62111C 20.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 67914 21.INSTALL FRONT DOOR SCUFF PLATE LH

a.

Attach the 6 claws and 3 clips to install the front door scuff plate LH.


Hide 67913 22.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 23.INSTALL FRONT SEAT ASSEMBLY (for Center Seat)

Hide 25.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).