Home › Vehicle Interior › INTERIOR › ROOF HEADLINING(for Double Cab)
RM27M0U _58 Vehicle Interior _049165 INTERIOR _0234502 ROOF HEADLINING(for Double Cab) A

INTERIOR  ROOF HEADLINING(for Double Cab)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 63310 1.INSTALL ROOF HEADLINING ASSEMBLY

B356809

a.

Place the roof headlining assembly into the cabin as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining assembly when placing it in the cabin.



b.

Attach the 4 clips to install the roof headlining assembly.


c.

Attach the 4 wire harness clamps and connect the connector to the front pillar LH.


d.

w/ EC Mirror:

Connect the connector.


Hide 74631C 2.INSTALL COAT HOOK

HINT:

Use the same procedure to install the coat hook on the other side.


a.
B168150

Assemble the coat hook as shown in the illustration.


b.

Attach the clip to install the coat hook.


Hide 74610A 3.INSTALL ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure for all the assist grip sub-assemblies.


a.
B165740

Assemble the assist grip sub-assembly as shown in the illustration.


b.

Attach the 2 clips to install the assist grip sub-assembly.


Hide 74348 5.INSTALL VISOR HOLDER

HINT:

Use the same procedure to install the visor holder on the other side.


a.

Using a T20 "TORX" driver, install the visor holder with the "TORX "screw.


Hide 74320 6.INSTALL VISOR ASSEMBLY LH

a.

w/ Vanity Light:

Connect the connector.


b.

Attach the claw to install the visor assembly LH.


c.

Install the 2 screws.


Hide 74310 7.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 87834 9.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 63650A 10.INSTALL ROOF CONSOLE BOX ASSEMBLY

Hide 62520P 11.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

a.

Pass the rear seat outer belt assembly through the hole of the front quarter trim panel assembly LH.


b.

Attach the 4 clips to install the front quarter trim panel assembly LH.


c.

Install the 2 bolts.


d.
B356806

Attach the claw to close the cover.


Hide 62510P 12.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62540 13.INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY LH

a.

Attach the 6 clips to install the lower quarter trim panel assembly LH.


b.

Connect the rear seat outer belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

Attach the 2 claws to install the cover.


Hide 62530 14.INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 73024 15.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

B166614

a.

Slide the front shoulder belt anchor plate sub-assembly LH in the direction of the arrow and attach the 6 claws to install it.


Hide 73023 16.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62412 17.INSTALL CENTER PILLAR GARNISH LH

a.

Pass the front seat outer belt assembly LH through the hole of the center pillar garnish LH.


b.

Attach the guide and clip to install the center pillar garnish LH.


c.

Install the bolt.


d.

Install the rear assist grip assembly to the center pillar garnish LH with the 2 bolts.


e.

Attach the 2 claws to close the 2 assist grip covers.

B355480


Hide 62411 18.INSTALL CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 62414A 19.INSTALL LOWER CENTER PILLAR GARNISH LH

a.

Attach the 7 clips and 2 claws to install the lower center pillar garnish LH.


b.

Connect the front seat outer belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

Attach the 2 claws to install the cover.


Hide 62413A 20.INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 62212 21.INSTALL FRONT PILLAR GARNISH LH

a.

Attach the clip to install the front pillar garnish LH.


b.

Install the bolt.


c.
B355362

Attach the claw to close the cover.


Hide 62211 22.INSTALL FRONT PILLAR GARNISH RH

a.

Attach the clip to install the front pillar garnish RH.


b.

Install the front assist grip sub-assembly to the front pillar garnish RH with the 2 bolts.


c.
B355365

Attach the 2 claws to close the 2 assist grip covers.


Hide 62332A 23.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.

Install the rear door opening trim weatherstrip LH.


Hide 62331A 24.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 62312B 25.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Install the front door opening trim weatherstrip LH.


Hide 62311B 26.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 62112 27.INSTALL COWL SIDE TRIM BOARD LH

a.

Attach the 2 clips to install the cowl side trim board LH.


b.

Install the nut.


Hide 62111C 28.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 67918B 29.INSTALL REAR DOOR SCUFF PLATE LH

a.

Attach the 6 claws and 2 clips to install the rear door scuff plate LH.


Hide 67917B 30.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 67914 31.INSTALL FRONT DOOR SCUFF PLATE LH

a.

Attach the 6 claws and 3 clips to install the front door scuff plate LH.


Hide 67913 32.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 34.INSTALL FRONT SEAT ASSEMBLY (for Center Seat)

Hide 35.INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)

Hide 36.INSTALL FRONT SEAT ASSEMBLY (for Power Seat)

Hide 37.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).