Home › Vehicle Interior › SLIDING ROOF › SLIDING ROOF HOUSING(for CrewMax)
RM27M0U _58 Vehicle Interior _049166 SLIDING ROOF _0234507 SLIDING ROOF HOUSING(for CrewMax) A

SLIDING ROOF  SLIDING ROOF HOUSING(for CrewMax)  INSTALLATION  


PROCEDURE

Hide 63203F 1.INSTALL SLIDING ROOF HOUSING SUB-ASSEMBLY

a.

Temporarily install the housing with the 10 bolts (vehicle body side) and 6 nuts.

B170247


b.

Tighten the 6 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Tighten the 10 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


d.
B170256E01
0.885,1.457 1.141,1.639 0.256,0.181 10 Clip 2.589,1.427 3.270,1.609 0.681,0.181 10 Outer Side 1.34,4.118 1.998,4.300 0.658,0.181 10 Front Side 0.985,1.149 1.068,1.425 false

Connect the 4 sliding roof drain hoses.

NOTICE:

The clip must face toward the outside of the vehicle and also be above the lower surface of the sliding roof housing when installing the drain hoses.



Hide 63251H 2.INSTALL SLIDING ROOF WEATHERSTRIP

B170258E01
1.448,1.191 1.726,1.684 false 0.71,1.761 1.445,1.944 0.735,0.183 10 Rear Side 0.04,2.146 0.537,2.302 0.496,0.156 10 Correct 0.882,1.076 1.356,1.290 0.475,0.214 10 Cutout 0.04,3.499 0.629,3.655 0.589,0.156 10 Incorrect

a.

Install the sliding roof weatherstrip as described below.

i.

Attach each corner of the weatherstrip so that each weatherstrip mark is aligned with the sliding roof glass' center mark. After attaching the entire weatherstrip, check that all weatherstrip marks are within the sliding roof glass' end marks.


ii.

Make sure the weatherstrip's cutout is toward the rear side of the vehicle and centered.


iii.

Make sure the weatherstrip is securely installed as shown in the illustration.



Hide 63201G 3.INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY

a.
B170246

Using a T25 "TORX" driver, temporarily install the glass with the 4 screws.


b.

Perform a level check.

B170255E03
2.448,1.573 2.448,1.188 false 1.948,1.948 2.229,1.948 false 2.552,1.948 2.833,1.948 false 2.75,2.542 2.583,2.396 false 4.458,1.406 4.615,1.583 0.156,0.177 10 false a 4.885,0.958 5.219,1.135 0.333,0.177 10 false Even 1.823,1.865 1.979,2.042 0.156,0.177 10 false A 2.24,1.865 2.396,2.042 0.156,0.177 10 false A 2.427,1.865 2.583,2.042 0.156,0.177 10 false B 2.865,1.865 3.021,2.042 0.156,0.177 10 false B 2.292,1.115 2.427,1.292 0.135,0.177 10 true C 2.302,1.5 2.458,1.677 0.156,0.177 10 false C 2.458,2.281 2.563,2.438 0.104,0.156 10 true D 2.708,2.552 2.865,2.729 0.156,0.177 10 true D

i.

Check the difference in the level between the roof panel and the upper surface of the weatherstrip labeled "a" when the sliding roof glass is fully closed.

Standard:
Area Measurement
A - A 0 +/-1.5 mm (0 +/-0.0591 in.)
B - B
C - C
D - D


HINT:

"+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.



ii.

Perform a gap check.

Check the gap between the roof panel and roof glass.

NOTICE:

The gap must be even all around.




c.
B171168

Tighten the 4 screws.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 4.CHECK FOR WATER LEAK

a.

After adjusting the sliding roof glass sub-assembly, check for water leak.


b.

If there are any leaks, readjust the sliding roof glass sub-assembly.


Hide 63218M 5.INSTALL SLIDING ROOF SIDE GARNISH LH

B231300

a.

Attach the 6 claws to install the sliding roof side garnish.


Hide 63217K 6.INSTALL SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 62180A 7.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH

Hide 62170A 8.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 63310 9.INSTALL ROOF HEADLINING ASSEMBLY

a.

Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 11.CHECK SRS WARNING LIGHT