Home › Power Source / Network › MULTIPLEX COMMUNICATION › LIN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049167 MULTIPLEX COMMUNICATION _0234509 LIN COMMUNICATION SYSTEM C

MULTIPLEX COMMUNICATION  LIN COMMUNICATION SYSTEM  B1206  P/W Master Switch Communication Stop  


DESCRIPTION

This DTC is output when LIN communication between the power window regulator master switch assembly and main body ECU (driver side junction block) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B1206 No communication between the power window regulator master switch assembly and main body ECU (driver side junction block) for 10 seconds or more.
·

Power window regulator master switch assembly

·

Main body ECU (driver side junction block)

·

Harness or connector



WIRING DIAGRAM

E344932E01
1.531,1.25 1.865,1.406 0.333,0.156 10 false LIN2 1.938,1.115 2.135,1.271 0.198,0.156 10 false 10 0.552,1.969 0.75,2.125 0.198,0.156 10 false J2 5.406,0.75 5.604,0.906 0.198,0.156 10 false B 5.417,1.24 5.781,1.396 0.365,0.156 10 false LIN1 5.406,1.677 5.542,1.833 0.135,0.156 10 false E 5.198,1.563 5.313,1.719 0.115,0.156 10 false 1 5.208,1.094 5.323,1.25 0.115,0.156 10 false 6 5.208,0.625 5.333,0.781 0.125,0.156 10 false 3 4.354,0.875 5.229,1.042 0.875,0.167 10 false POWER No.3 0.552,2.156 2.323,2.5 1.771,0.344 10 false Main Body ECU (Driver Side Junction Block) 0.677,2.865 2.313,3.104 1.635,0.24 10 false : LIN Communication Line 5.177,2.5 6.948,2.844 1.771,0.344 10 false Power Window Regulator Master Switch Assembly 5.167,2.302 5.365,2.458 0.198,0.156 10 false N2 3.219,0.708 4.094,0.875 0.875,0.167 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:

When using the Techstream with the ignition switch OFF to troubleshoot:

Connect the Techstream to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.


HINT:

DTC B2325 is stored when communication between the master switch and main body ECU (driver side junction block) stops.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1206 output reoccurs A
DTC B1206 output does not reoccur B



A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MASTER SWITCH)

B

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MASTER SWITCH)
a.
U152787E02
2.25,1.656 2.51,1.781 false 2.083,3.969 2.49,3.469 false 1.052,1.375 1.25,1.552 0.198,0.177 10 false J2 0.844,3.865 1.052,4.042 0.208,0.177 10 false N2 0.104,0.052 2.469,0.448 2.365,0.396 10 false Front view of wire harness connector: (to Main Body ECU) 0.104,2.344 2.469,2.885 2.365,0.542 10 false Front view of wire harness connector: (to Power Window Regulator Master Switch Assembly) 2.552,1.729 2.906,1.927 0.354,0.198 10 false LIN2 2.552,3.302 2.969,3.51 0.417,0.208 10 false LIN1

Disconnect the J2 main body ECU (driver side junction block) connector.


b.

Disconnect the N2 power window regulator master switch assembly connector.


c.

Measure the resistance according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
J2-10 (LIN2) - N2-6 (LIN1) Always Below 1 Ω
J2-10 (LIN2) or N2-6 (LIN1) - Body ground Always 10 kΩ or higher




OK

4.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (MASTER SWITCH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (MASTER SWITCH - BATTERY AND BODY GROUND)
a.
U152788E02
1.677,1.688 1.302,1.26 false 1.156,1.646 1.427,1.708 false 2.823,1.625 3.031,1.802 0.208,0.177 10 false N2 0.083,0.063 2.521,0.604 2.438,0.542 10 false Front view of wire harness connector: (to Power Window Regulator Master Switch Assembly) 1.188,1.094 1.323,1.271 0.135,0.177 10 false B 1.042,1.552 1.167,1.729 0.125,0.177 10 false E

Disconnect the N2 power window regulator master switch assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-1 (E) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
N2-3 (B) - Body ground Always 11 to 14 V




OK

5.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Temporarily replace the power window regulator master switch assembly with a new or normally functioning one (See page Vehicle Interior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).




NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1206 output does not reoccur A
DTC B1206 output reoccurs B



A

END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY IS DEFECTIVE)

B

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)