Home › Power Source / Network › MULTIPLEX COMMUNICATION › LIN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049167 MULTIPLEX COMMUNICATION _0234509 LIN COMMUNICATION SYSTEM C

MULTIPLEX COMMUNICATION  LIN COMMUNICATION SYSTEM  B2322  Front Passenger Side Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the front power window regulator motor assembly RH and main body ECU (driver side junction block) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2322 No communication between the front power window regulator motor assembly RH and main body ECU (driver side junction block) for 10 seconds or more.
·

Front power window regulator motor assembly RH

·

Main body ECU (driver side junction block)

·

Harness or connector



WIRING DIAGRAM

E344932E03
1.531,1.25 1.865,1.406 0.333,0.156 10 false LIN2 1.938,1.115 2.135,1.271 0.198,0.156 10 false 10 0.552,1.969 0.75,2.125 0.198,0.156 10 false J2 5.406,0.75 5.604,0.906 0.198,0.156 10 false B 5.417,1.24 5.781,1.396 0.365,0.156 10 false LIN 5.406,1.677 5.76,1.833 0.354,0.156 10 false GND 5.198,1.563 5.313,1.719 0.115,0.156 10 false 1 5.208,1.094 5.323,1.25 0.115,0.156 10 false 9 5.208,0.625 5.333,0.781 0.125,0.156 10 false 2 4.354,0.875 5.229,1.042 0.875,0.167 10 false POWER No.4 0.552,2.156 2.323,2.5 1.771,0.344 10 false Main Body ECU (Driver Side Junction Block) 0.677,2.865 2.313,3.104 1.635,0.24 10 false : LIN Communication Line 5.167,2.49 7.115,2.885 1.948,0.396 10 false Front Power Window Regulator Motor Assembly RH 5.167,2.302 5.49,2.5 0.323,0.198 10 false M11 3.219,0.708 4.094,0.875 0.875,0.167 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:

When using the Techstream with the ignition switch OFF to troubleshoot:

Connect the Techstream to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.


HINT:

DTC B2325 is output when communication between the front power window regulator motor assembly RH and main body ECU (driver side junction block) stops.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2322 output reoccurs A
DTC B2322 output does not reoccur B



A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REGULATOR MOTOR RH)

B

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REGULATOR MOTOR RH)
a.
U152790E02
2.24,1.635 2.698,1.479 false 2.021,4.292 2.281,4.448 false 1.052,1.406 1.25,1.583 0.198,0.177 10 false J2 0.99,3.792 1.281,3.969 0.292,0.177 10 false M11 0.26,0.042 2.625,0.438 2.365,0.396 10 false Front view of wire harness connector: (to Main Body ECU) 0.125,2.219 2.688,2.74 2.563,0.521 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly RH) 2.771,1.385 3.083,1.563 0.313,0.177 10 false LIN2 2.333,4.365 2.563,4.542 0.229,0.177 10 false LIN

Disconnect the J2 main body ECU (driver side junction block) connector.


b.

Disconnect the M11 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J2-10 (LIN2) - M11-9 (LIN) Always Below 1 Ω
J2-10 (LIN2) or M11-9 (LIN) - Body ground Always 10 kΩ or higher




OK

4.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (REGULATOR MOTOR RH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (REGULATOR MOTOR RH - BATTERY AND BODY GROUND)
a.
U152792E02
2.063,2.219 2.406,1.99 false 1.708,2.219 1.333,1.979 false 1.083,2.448 1.385,2.625 0.302,0.177 10 false M11 0.125,0.146 2.458,0.76 2.333,0.615 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly RH) 2.448,1.875 2.604,2.052 0.156,0.177 10 false B 1.01,1.865 1.333,2.042 0.323,0.177 10 false GND

Disconnect the M11 front power window regulator motor assembly RH connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
M11-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
M11-2 (B) - Body ground Always 11 to 14 V




OK

5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Temporarily replace the front power window regulator motor assembly RH with a new or normally functioning one (See page Vehicle Interior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL).




NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2322 output does not reoccur A
DTC B2322 output reoccurs B



A

END (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH IS DEFECTIVE)

B

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)