Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Either condition is met:
·

"Spiral cable (Steering Angle Sensor)" is not displayed on the "Bus Check" screen.

·

"Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside steering angle sensor

·

Steering angle sensor CAN branch wire or connector

·

Steering angle sensor



WIRING DIAGRAM

C280376E17
0.531,1.823 0.813,1.979 0.281,0.156 10 false J75 0.531,1.979 2.094,2.167 1.563,0.188 10 false No. 1 Junction Connector 1.74,3.448 3.052,3.667 1.313,0.219 10 false from IG1 NO.1 Relay 2.24,2.646 4.281,2.99 2.042,0.344 10 false from Battery 4.083,2.5 4.677,2.677 0.594,0.177 10 false ECU-B1 4,3.292 5.052,3.698 1.052,0.406 10 false ECU-IG NO.1 1.688,1.344 1.875,1.521 0.188,0.177 10 false 17 1.677,0.771 1.823,0.927 0.146,0.156 10 false 6 5.677,0.885 6.604,1.26 0.927,0.375 10 false CANH 5.688,1.448 6.615,1.823 0.927,0.375 10 false CANL 5.688,2.635 6.615,3.01 0.927,0.375 10 false BAT 5.698,3.448 6.625,3.823 0.927,0.375 10 false IG 5.677,4.115 6.604,4.49 0.927,0.375 10 false ESS 5.427,4 5.542,4.188 0.115,0.188 11 false 2 5.427,3.344 5.594,3.542 0.167,0.198 11 false 1 5.438,2.51 5.563,2.698 0.125,0.188 11 false 3 5.427,1.323 5.552,1.51 0.125,0.188 11 false 9 5.344,0.719 5.552,0.906 0.208,0.188 11 false 10 5.302,4.938 5.479,5.115 0.177,0.177 10 false J6 5.292,5.104 6.677,5.313 1.385,0.208 10 false Steering Angle Sensor

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
a.
U152505E01
1.172,1.309 0.944,1.537 0.944,1.537 0.834,1.537 false 1.008,1.802 1.068,1.802 1.068,1.802 1.307,1.309 false 0.338,1.451 0.759,1.594 0.421,0.143 10 CANH 1.688,0.335 1.855,0.478 0.167,0.143 10 J6 0.51,1.72 0.931,1.863 0.421,0.143 10 CANL 0.058,0.035 0.253,0.178 0.195,0.143 10 *a

Disconnect the J6 steering angle sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J6-10 (CANH) - J6-9 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Steering Angle Sensor)



OK

4.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE STEERING ANGLE SENSOR CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)
a.
U152506E01
2.213,1.309 2.441,1.537 2.441,1.537 2.551,1.537 false 2.376,1.802 2.316,1.802 2.316,1.802 2.078,1.309 false 2.59,1.451 3.011,1.594 0.421,0.143 10 ESS 2.673,0.987 3.094,1.130 0.421,0.143 10 IG 0.499,1.187 0.666,1.330 0.167,0.143 10 J6 2.401,1.72 2.821,1.863 0.421,0.143 10 BAT 0.058,0.035 0.253,0.178 0.195,0.143 10 *a 2.348,1.23 2.545,1.062 2.545,1.062 2.651,1.062 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J6-2 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J6-3 (BAT) - Body ground Always 11 to 14 V
J6-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Steering Angle Sensor)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR