Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Main Body ECU Communication Stop Mode Either condition is met:
·

"Main Body" is not displayed on the "Bus Check" screen.

·

"Main Body ECU Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside of main body ECU (driver side junction block assembly)

·

Main body ECU (driver side junction block assembly) CAN branch wire or connector

·

Main body ECU (driver side junction block assembly)



WIRING DIAGRAM

C288319E04
5.625,0.896 6.042,1.063 0.417,0.167 10 false CANH 5.615,1.375 5.99,1.552 0.375,0.177 10 false CANL 1.656,0.781 1.802,0.958 0.146,0.177 10 false 5 0.448,1.74 0.729,1.885 0.281,0.146 10 false J75 0.427,1.896 2.01,2.104 1.583,0.208 10 false No. 1 Junction Connector 1.646,1.25 1.844,1.427 0.198,0.177 10 false 16 5.635,2.865 6.042,3.052 0.406,0.188 10 false BECU 5.635,3.5 6.031,3.688 0.396,0.188 10 false ALTB 5.635,4.083 5.99,4.26 0.354,0.177 10 false ACC 5.656,5.073 5.875,5.271 0.219,0.198 10 false IG 5.656,6.073 6.073,6.25 0.417,0.177 10 false GND1 1.917,2.698 2.427,2.875 0.51,0.177 10 false ECU-B1 0.698,2.854 1.469,3.042 0.771,0.188 10 false from Battery 4.583,3.344 5.104,3.51 0.521,0.167 10 false DR/LCK 4.458,4.906 5.302,5.094 0.844,0.188 10 false ECU-IG No.2 4.667,3.917 5,4.083 0.333,0.167 10 false ACC 2.771,2.875 2.99,3.042 0.219,0.167 10 false DB 2.792,2.635 2.969,2.802 0.177,0.167 10 false 13 2.781,6.063 3,6.229 0.219,0.167 10 false DB 2.802,5.854 2.99,6.021 0.188,0.167 10 false 21 2.781,3.521 3,3.688 0.219,0.167 10 false DA 2.844,3.281 2.948,3.417 0.104,0.135 10 false 1 3.594,4.583 3.917,4.76 0.323,0.177 10 false ACC 3.448,5.583 4.031,5.771 0.583,0.188 10 false IG1 No.3 2.771,5.333 2.99,5.5 0.219,0.167 10 false DD 2.792,5.115 2.969,5.271 0.177,0.156 10 false 43 2.771,4.333 2.969,4.49 0.198,0.156 10 false DD 2.802,4.094 2.979,4.25 0.177,0.156 10 false 45 0.719,3.479 1.49,3.698 0.771,0.219 10 false from Battery 0.302,4.333 1.51,4.51 1.208,0.177 10 false from Ignition Switch 5.292,1.385 5.448,1.552 0.156,0.167 10 false J2 5.292,1.188 5.396,1.344 0.104,0.156 10 false 6 5.281,0.896 5.448,1.063 0.167,0.167 10 false J2 5.302,0.646 5.396,0.833 0.094,0.188 10 false 5 3.51,7.052 5.813,7.469 2.302,0.417 10 false Main Body ECU (Driver Side Junction Block Assembly)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and relays for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU CAN BRANCH WIRE)
a.
U152508E01
1.53,1.359 1.871,1.926 1.871,1.926 2.01,1.926 false 1.414,1.359 1.073,1.926 1.073,1.926 0.935,1.926 false 2.057,1.853 2.478,1.989 0.422,0.137 10 CANL 0.385,1.853 0.807,1.989 0.422,0.137 10 CANH 0.7,1.161 0.876,1.298 0.176,0.137 10 J2 0.067,0.048 0.267,0.185 0.199,0.137 10 *a

Disconnect the J2 main body ECU (driver side junction block assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J2-5 (CANH) - J2-6 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Driver Side Junction Block Assembly])



OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE MAIN BODY ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

U152728E01
0.227,0.14 0.464,0.363 0.237,0.223 10 *a 1.043,0.796 1.255,0.940 0.211,0.144 10 DA 0.268,2.441 0.726,2.594 0.458,0.152 10 ALTB 6.279,0.975 6.699,1.137 0.420,0.163 10 ACC 6.46,1.203 6.880,1.366 0.420,0.163 10 IG 1.038,2.043 0.753,2.505 0.753,2.505 0.62,2.505 false 3.189,1.064 3.401,1.208 0.211,0.144 10 DB 5.45,1.064 5.669,1.208 0.218,0.144 10 DD 2.712,2.231 3.149,2.390 0.437,0.159 10 BECU 2.467,1.828 2.565,2.291 2.565,2.291 2.698,2.291 false 3.735,2.231 4.172,2.390 0.437,0.159 10 GND1 3.517,1.94 3.587,2.291 3.587,2.291 3.721,2.291 false 6.019,1.743 6.304,1.28 6.304,1.28 6.437,1.28 false 5.847,1.745 6.12,1.039 6.12,1.039 6.254,1.039 false

Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Driver Side Junction Block Assembly])
- -

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the DA, DB and DD main body ECU (driver side junction block assembly) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DB-21 (GND1) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DA-1 (ALTB) - Body ground Always 11 to 14 V
DB-13 (BECU) - Body ground Always 11 to 14 V
DD-43 (IG) - Body ground Ignition switch ON 11 to 14 V
DD-45 (ACC) - Body ground Ignition switch ACC 11 to 14 V




OK

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR