Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Navigation ECU Communication Stop Mode  


DESCRIPTION

Detection Condition Symptoms Trouble Area
Navigation ECU Communication Stop Mode Either condition is met:
·

"Display and Navigation (AVN1)" is not displayed on the "Bus Check" screen.

·

"Audio Receiver Assembly Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside of navigation receiver assembly

·

Navigation receiver assembly CAN branch wire or connector

·

Navigation receiver assembly



For vehicles a navigation system.


WIRING DIAGRAM

C289528E06
5.229,1.167 5.406,1.333 0.177,0.167 10 false 10 5.24,0.583 5.344,0.74 0.104,0.156 10 false 9 5.26,3.917 5.365,4.052 0.104,0.135 10 false 7 5.125,0.833 5.469,1.01 0.344,0.177 10 false J135 5.146,1.417 5.469,1.594 0.323,0.177 10 false J135 5.125,4.167 5.469,4.323 0.344,0.156 10 false J133 5.583,1.396 5.99,1.563 0.406,0.167 10 false CANL 5.573,0.833 6.021,1 0.448,0.167 10 false CANH 5.594,4.156 6.01,4.344 0.417,0.188 10 false GND1 0.448,1.76 0.656,1.917 0.208,0.156 10 false J74 0.438,1.906 2,2.115 1.563,0.208 10 false No. 2 Junction Connector 1.594,1.302 1.802,1.479 0.208,0.177 10 false 18 1.615,0.75 1.729,0.885 0.115,0.135 10 false 7 5.135,2.417 5.458,2.583 0.323,0.167 10 false J133 5.25,2.156 5.344,2.323 0.094,0.167 10 false 4 5.594,2.417 5.875,2.604 0.281,0.188 10 false +B1 2.25,2.406 3.01,2.594 0.76,0.188 10 false from Battery 3.917,2.25 4.594,2.438 0.677,0.188 10 false RAD NO.1 5.271,2.74 5.385,2.906 0.115,0.167 10 false 3 5.135,3 5.458,3.156 0.323,0.156 10 false J133 5.604,3.01 5.99,3.177 0.385,0.167 10 false ACC1 2.042,2.958 3.042,3.156 1,0.198 10 false from ACC Relay 4.083,2.823 4.406,3.021 0.323,0.198 10 false ACC 5.271,3.344 5.375,3.479 0.104,0.135 10 false 1 5.135,3.583 5.458,3.76 0.323,0.177 10 false J135 5.583,3.583 5.781,3.75 0.198,0.167 10 false IG 1.854,3.573 3.021,3.781 1.167,0.208 10 false from IG No.1 Relay 4.052,3.427 4.438,3.594 0.385,0.167 10 false LH-IG 5.021,4.927 6.927,5.135 1.906,0.208 10 false Navigation Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY CAN BRANCH WIRE)
a.
U152463E01
0.047,0.049 0.252,0.218 0.205,0.170 10 *a 1.553,0.362 1.877,0.503 0.324,0.140 10 J135 2.039,1.299 2.26,1.774 2.26,1.774 2.366,1.774 false 1.908,1.299 1.687,1.774 1.687,1.774 1.581,1.774 false 1.079,1.699 1.490,1.837 0.411,0.139 10 CANH 2.398,1.699 2.809,1.837 0.411,0.139 10 CANL

Disconnect the J135 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J135-9 (CANH) - J135-10 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE NAVIGATION RECEIVER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U152465E01
0.047,0.049 0.252,0.218 0.205,0.170 10 *a 2.002,2.492 2.202,2.18 2.202,2.18 2.307,2.18 false 2.201,2.601 2.4,2.812 2.4,2.812 2.505,2.812 false 1.65,2.79 1.472,3.132 1.472,3.132 1.366,3.132 false 0.511,0.93 0.676,1.068 0.165,0.139 10 IG 0.864,3.056 1.275,3.195 0.411,0.139 10 GND1 2.522,2.734 2.933,2.873 0.411,0.139 10 +B1 2.329,2.103 2.740,2.241 0.411,0.139 10 ACC1 0.713,1.003 0.804,1.003 0.804,1.003 0.953,1.218 false 1.536,0.415 1.860,0.555 0.324,0.140 10 J135 1.536,1.858 1.860,1.999 0.324,0.140 10 J133

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the J133 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J133-7 (GND1) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J133-4 (+B1) - Body ground Always 11 to 14 V
J133-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
J135-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)

Result
Result Proceed to
OK (for Column Shift Type) A
OK (for Floor Shift Type) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR