Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM C

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  U0208  Lost Communication with "Seat Control Module A"  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0208 There is no communication from the front power seat control ECU with switch LH.
·

Power source or inside front power seat control ECU and switch LH

·

Front power seat control ECU and switch LH CAN branch wire or connector

·

Front power seat control ECU and switch LH



For vehicles with a seat memory.


WIRING DIAGRAM

C251476E25
3.656,2.771 4.188,2.938 0.531,0.167 10 false ECU-B1 5.604,1.208 6.042,1.396 0.438,0.188 10 false CANN 5.604,2.938 6.031,3.104 0.427,0.167 10 false SYSB 5.604,3.365 6,3.521 0.396,0.156 10 false GND1 5.604,2.406 5.906,2.563 0.302,0.156 10 false +B1 5.323,0.594 5.406,0.75 0.083,0.156 10 false 8 5.24,0.792 5.5,0.948 0.26,0.156 10 false Z10 5.323,1.021 5.417,1.156 0.094,0.135 10 false 7 5.24,1.208 5.5,1.385 0.26,0.177 10 false Z10 5.313,2.198 5.406,2.333 0.094,0.135 10 false 7 5.271,2.396 5.458,2.552 0.188,0.156 10 false Z9 5.313,3.167 5.406,3.323 0.094,0.156 10 false 2 5.271,3.365 5.458,3.531 0.188,0.167 10 false Z9 5.271,2.708 5.458,2.875 0.188,0.167 10 false 12 5.24,2.906 5.479,3.073 0.24,0.167 10 false Z10 5.604,0.813 6.052,0.99 0.448,0.177 10 false CANP 1.646,1.104 1.813,1.281 0.167,0.177 10 false 14 1.646,0.688 1.802,0.854 0.156,0.167 10 false 3 0.427,1.604 0.719,1.771 0.292,0.167 10 false J76 0.427,1.75 1.99,1.938 1.563,0.188 10 false No. 3 Junction Connector 1.75,2.375 2.5,2.573 0.75,0.198 10 false from Battery 1.75,2.885 2.521,3.073 0.771,0.188 10 false from Battery 3.458,2.25 4.417,2.438 0.958,0.188 10 false FR P/SEAT LH 5.219,4.146 6.813,4.521 1.594,0.375 10 false Front Power Seat Control ECU and Switch LH

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any other switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (FRONT POWER SEAT CONTROL ECU AND SWITCH LH CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (FRONT POWER SEAT CONTROL ECU AND SWITCH LH CAN BRANCH WIRE)
a.
U152448E01
0.078,0.09 0.251,0.258 0.173,0.168 10 *a 2.574,1.696 3.009,1.834 0.435,0.138 10 CANN 2.439,1.919 2.874,2.058 0.435,0.140 10 CANP 2.547,1.767 2.447,1.767 2.447,1.767 2.327,1.616 false 2.424,1.994 2.327,1.994 2.327,1.994 2.231,1.616 false 1.213,1.326 1.469,1.463 0.257,0.138 10 Z10

Disconnect the Z10 front power seat control ECU and switch LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
Z10-8 (CANP) - Z10-7 (CANN) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Front Power Seat Control ECU and Switch LH)



OK

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT CONTROL ECU AND SWITCH LH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE FRONT POWER SEAT CONTROL ECU AND SWITCH LH CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT CONTROL ECU AND SWITCH LH - BATTERY AND BODY GROUND)
a.
U152449E02
0.865,1.802 0.927,1.802 0.927,1.802 1.49,1.396 false 1.854,1.854 1.938,1.854 1.938,1.854 2.083,1.583 false 0.781,0.76 0.844,0.76 0.844,0.76 1.385,1.219 false 0.281,0.104 0.458,0.271 0.177,0.167 10 false *a 0.542,1.708 0.823,1.896 0.281,0.188 10 false +B1 1.417,1.771 1.854,1.938 0.438,0.167 10 false SYSB 0.26,1.146 0.458,1.344 0.198,0.198 10 false Z9 2.927,1.156 3.167,1.344 0.24,0.188 10 false Z10 0.375,0.667 0.781,0.854 0.406,0.188 10 false GND1

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the Z9 front power seat control ECU and switch LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z9-2 (GND1) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Z9-7 (+B1) - Body ground Always 11 to 14 V
Z10-12 (SYSB) - Body ground Always 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Front Power Seat Control ECU and Switch LH)


OK

REPLACE FRONT POWER SEAT CONTROL ECU AND SWITCH LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR