Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Bus Buffer ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Bus Buffer ECU Communication Stop Mode Either condition is met:
·

"Accessory Gateway" is not displayed on the "Bus Check" screen.

·

"Bus Buffer ECU Communication Stop Mode" in "DTC Combination Table" applies.


·

Bus buffer ECU CAN branch wire or connector

·

Bus buffer ECU



WIRING DIAGRAM

C288320E11
5.594,1.875 5.854,2.031 0.26,0.156 10 false J59 5.594,2.042 6.583,2.229 0.99,0.188 10 false Bus Buffer ECU 5.635,0.865 6.188,1.01 0.552,0.146 10 false CAN+ 1.656,1.375 1.854,1.521 0.198,0.146 10 false 16 1.677,0.781 1.802,0.948 0.125,0.167 10 false 5 5.406,1.354 5.51,1.5 0.104,0.146 10 false 2 5.406,0.781 5.51,0.927 0.104,0.146 10 false 3 0.344,1.865 0.583,2.021 0.24,0.156 10 false J74 0.344,2.031 1.917,2.198 1.573,0.167 10 false No. 2 Junction Connector 5.646,1.469 6.198,1.615 0.552,0.146 10 false CAN-

CAUTION / NOTICE / HINT

HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK FOR OPEN IN CAN BUS WIRE (BUS BUFFER ECU CAN BRANCH WIRE)
3.CHECK FOR OPEN IN CAN BUS WIRE (BUS BUFFER ECU CAN BRANCH WIRE)
a.
U152607E01
0.878,1.823 1.395,1.965 0.517,0.142 10 CAN- 2.375,1.823 2.892,1.965 0.517,0.142 10 CAN+ 0.119,0.092 0.636,0.234 0.517,0.142 10 *a 0.516,1.084 0.760,1.226 0.244,0.142 10 J59 1.996,1.424 2.15,1.901 2.15,1.901 2.326,1.901 false 1.696,1.424 1.543,1.901 1.543,1.901 1.366,1.901 false

Disconnect the J59 bus buffer ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J59-3 (CAN+) - J59-2 (CAN-) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Bus Buffer ECU)



OK

REPLACE BUS BUFFER ECU

NG

REPAIR OR REPLACE BUS BUFFER ECU CAN BRANCH WIRE OR CONNECTOR (CAN+, CAN-)